manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine General Information and Diagnosis:  1A-189

Troubleshooting

NOTE:

• Before performed trouble shooting, be sure to read the “Precautions of ECM Circuit Inspection: ”.
• When measuring circuit voltage, resistance and/or pulse signal at ECM connector, connect the 

special tool to ECM and/or the ECM connectors referring to “Inspection of ECM and Its Circuits: ”.

 

1. Blower fan motor

8. Radiator cooling fan motor relay 

No.1

15. BCM

22. “IG ACC” fuse

2. Blower fan switch

9. Radiator cooling fan motor relay 

No.2

16. Evaporator outlet air temp. 

sensor

23. “RDTR FAN” fuse

3. A/C switch

10. Radiator cooling fan motor relay 

No.3

17. “IG1 SIG” fuse

24. Junction block assembly

4. A/C refrigerant pressure 

sensor

11. Radiator cooling fan motor

18. Relay box

25. “IG2 SIG” fuse

5. Blower motor relay

12. Main relay

19. “HTR FAN” fuse

6. Compressor relay

13. ECM

20. “FI” fuse

7. A/C compressor

14. Ignition switch

21. “A/C COMP” fuse

Step

Action

Yes

No

1

Reception data check from BCM

1) Connect scan tool to DLC with ignition switch turned 

OFF.

2) Turn ON ignition switch.
3) Check DTC for reception data from BCM.

Is there DTC P1678?

Go to applicable DTC 
diag. flow.

Go to Step 2.

2

A/C switch signal circuit check

1) Start engine and select “DATA LIST” mode on scan tool.
2) Check A/C switch signal under following conditions 

respectively.

A/C switch signal 
Engine running, A/C switch OFF: OFF
Engine running, A/C switch ON and blower speed 
selector turned 1st position or more: ON

Is check result satisfactory?

Go to Step 3.

Check A/C switch 
circuit.

3

DTC check of ECT sensor circuit

1) Check ECM for DTC of ECT sensor circuit.

Is there DTC P0116, DTC P0117 or DTC P0118?

Go to applicable DTC 
diag. flow.

Go to Step 4.

4

Radiator cooling fan control system check

Is radiator cooling fan started when A/C and blower speed 
selector switch are turned ON with engine running?

Go to Step 10.

Go to Step 5.

5

Radiator cooling fan control circuit check

1) Check DTC with scan tool.

Is DTC P0480 displayed?

Go to “DTC P0480: Fan 
1 (Radiator Cooling 
Fan) Control Circuit: ”.

Go to Step 6.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

RaceChip Pro 2 Installation Manual preview
Pro 2
Бренд: RaceChip Страницы: 12
Yakima K343 Manual preview
K343
Бренд: Yakima Страницы: 11
Car-Interface CI-RL4-ELINK Manual preview
CI-RL4-ELINK
Бренд: Car-Interface Страницы: 23
RuggON VD04 Quick Start Manual preview
VD04
Бренд: RuggON Страницы: 2
SnapPad EQ Round Installation Instructions preview
EQ Round
Бренд: SnapPad Страницы: 5
Quadratec 12057.0261 Installation Manual preview
12057.0261
Бренд: Quadratec Страницы: 12
Oldsmobile 2000 Oldsmobile Intrigue Owner'S Manual preview
2000 Oldsmobile Intrigue
Бренд: Oldsmobile Страницы: 348
Ferve F-2024 Operating Instructions Manual preview
F-2024
Бренд: Ferve Страницы: 28
Lexus 2010 RX 350 Warranty And Services Manual preview
2010 RX 350
Бренд: Lexus Страницы: 82
OMNISTOR Omni-Bike Sport Ducato Installation preview
Omni-Bike Sport Ducato
Бренд: OMNISTOR Страницы: 5
Easee Base 1-Way User Manual / Installation Manual preview
Base 1-Way
Бренд: Easee Страницы: 21
Flash Cover MN012 Installation Manual preview
MN012
Бренд: Flash Cover Страницы: 2
Conrad TPMS-001 Operating Instructions Manual preview
TPMS-001
Бренд: Conrad Страницы: 8
AA Products APX2501 BLK Instruction Manual preview
APX2501 BLK
Бренд: AA Products Страницы: 8
Safe Fleet PRIME DESIGN HRR-NV11B Manual preview
PRIME DESIGN HRR-NV11B
Бренд: Safe Fleet Страницы: 12
Honda 1996 Civic Del Sol Owner'S Manual preview
1996 Civic Del Sol
Бренд: Honda Страницы: 219
AA Products RB0002 Instruction Manual preview
RB0002
Бренд: AA Products Страницы: 6
VanEssa mobilcamping 00001668 Installation Manual preview
00001668
Бренд: VanEssa mobilcamping Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды