Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 419

Страница: 419 / 1257

Front Suspension: 2B-9

6) Pull brake disc (2) off by using two 8 mm bolts.

7) Pull out wheel hub (1) with special tools.

Special tool
(A): 09943-17912
(B): 09942-15511

CAUTION:

When wheel hub is removed, replace wheel
bearing with new one.

8) Disconnect tie-rod end (1) from steering knuckle (2)

with puller (3).

9) Remove wheel speed sensor (1) from knuckle (if

equipped with ABS).

10) Loosen strut bracket nuts (1).

11) Remove ball joint bolt (3) and nut (4).

12) Remove strut bracket bolts from strut bracket and

then steering knuckle (2).

13) Remove circlip from knuckle.
14) Using hydraulic press (1) and special tool, remove

wheel bearing.

Special tool
(A): 09913-75520

CAUTION:

When installing wheel bearing, replace it with
new one.

I2RH01220027-

I2RH01220028-

I4RS0A220017-

F: Forward

R: Rearward

I4RS0A220018-

I4RS0A220019-

I2RH01220033-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды