manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-138 Automatic Transmission: 

• Do not open rear cover seal ring too wide to attach.

• Do not damage O/D and 2nd coast brake return 

spring subassembly and piston by pressing in O/D 
and 2nd coast brake return spring subassembly 
passing through its original installing position over 1.0 
mm (0.039 in.).

Special tool
(A):  09926–96030
(B):  09946–06710

Transaxle Rear Cover (O/D and 2nd Coast Brake 
Piston) Assembly Inspection

S4RS0A5106045

O/D and 2nd Coast Brake Return Spring 
Subassembly

Measure free length of O/D and 2nd coast brake return 
spring.

Free length of O/D and 2nd coast brake return spring
“a”: 18.99 mm (0.748 in.)

NOTE:

• Do not apply excessive force when 

measuring spring free length.

• Perform measurement at several points.

 

Transaxle Rear Cover Bush

Measure transaxle rear cover bush bore by using special 
tool.
If measured transaxle rear cover bush bore is out of 
specifications, replace transaxle rear cover with new 
one. In replacement, intermediate shaft subassembly 
also needs to be checked. Replace intermediate shaft 
subassembly, if necessary.

Special tool
(A):  09900–20605

Transaxle rear cover bush bore
Standard: 13.94 – 13.96 mm (0.549 – 0.550 in.)

1. Transaxle rear cover

1. Transaxle rear cover

I2RH0B510206-

I2RH0B510201-

I2RH0B510207-

I2RH0B510208-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Saab B205 Installation Instructions Manual preview
B205
Бренд: Saab Страницы: 10
Warrior Products 10936 Installation Instructions preview
10936
Бренд: Warrior Products Страницы: 3
Blue Ox BX3781 Installation Instructions Manual preview
BX3781
Бренд: Blue Ox Страницы: 7
Shad NADSA ATV80 Owner'S Manual preview
NADSA ATV80
Бренд: Shad Страницы: 3
Safe Fleet RVS-082550 Instruction Manual preview
RVS-082550
Бренд: Safe Fleet Страницы: 11
Camec 042374 User Manual preview
042374
Бренд: Camec Страницы: 19
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Бренд: iRacing Страницы: 25
Caltrend CV445 Installation Instructions preview
CV445
Бренд: Caltrend Страницы: 2
Audiovox EM-2201 Installation Instructions preview
EM-2201
Бренд: Audiovox Страницы: 1
EGR EGR-3PVE-COLOUR Installation Instructions Manual preview
EGR-3PVE-COLOUR
Бренд: EGR Страницы: 28
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Бренд: Xpresskit Страницы: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Бренд: RAM Страницы: 92
Boyo VTL17LTJ Manual preview
VTL17LTJ
Бренд: Boyo Страницы: 9
Radical Sportscars SR 3 SL Owner'S Handbook Manual preview
SR 3 SL
Бренд: Radical Sportscars Страницы: 44
Oypla Leisure 4269 User Manual preview
4269
Бренд: Oypla Leisure Страницы: 4
INDIWORK A-LINK2-NTG5 Instruction Manual preview
A-LINK2-NTG5
Бренд: INDIWORK Страницы: 18
Opel CORSA 2020 Infotainment Manual preview
CORSA 2020
Бренд: Opel Страницы: 103
TATA Motors Indigo eCS Owner'S Manual & Service Book preview
Indigo eCS
Бренд: TATA Motors Страницы: 166

Бренды по названию

Популярные бренды

Загрузить еще бренды