manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1C-6 Engine Electrical Devices: 

Installation

Reverse removal procedure noting the following.
• Tighten heated oxygen sensor (1) to specified torque.

Tightening torque
Heated oxygen sensor (a):  45 N·m (4.5 kg-m, 32.5 
lb-ft)

• Install exhaust manifold referring to “Exhaust Manifold 

Removal and Installation:  in Section 1K”, if removed.

• Connect connector of heated oxygen sensor (1) and 

clamp wire harness securely.

• After installing heated oxygen sensor, start engine 

and check that no exhaust gas leakage exists.

Camshaft Position (CMP) Sensor Removal and 
Installation

S4RS0A1306013

Removal

1) Disconnect negative cable at battery.
2) Disconnect connector from CMP sensor.
3) Remove camshaft position sensor from cylinder 

head.

Installation

1) Install camshaft position sensor to cylinder head.

Tightening torque
CMP sensor bolt (a):  10 N·m (1.0 kg-m, 7.5 lb-ft)

2) Connect connector to CMP sensor securely.
3) Connect negative cable to battery.

Camshaft Position (CMP) Sensor Inspection

S4RS0A1306014

Visual check

• Check that O-ring is free from damage.
• Check that end face of sensor and signal rotor tooth 

are free from any metal particles and damage.

Performance check

1) Remove metal particles on end face of CMP sensor, 

if any.

2) Arrange 12 V battery (1) and connect its positive 

terminal to “Vin” terminal (2) and negative terminal to 
“Ground” terminal (3) of sensor. Then using 
ohmmeter, measure resistance between “Vout” 
terminal (4) of sensor and negative terminal of 
battery by passing magnetic substance (iron) (5) 
while keeping approximately 1 mm (0.03 in.) gap 
with respect to end face of CMP sensor.
If resistance does not vary as specified below, 
replace CMP sensor.

CMP sensor resistance
Resistance varies from less than 220 

:

 (ON) to 

infinity (OFF) or from infinity (OFF) to less than 220 

:

 (ON)

[A]: HO2S-1
[B]: HO2S-2

[A]

[B]

1, (a)

1, (a)

I3RM0A130007-

I4RS0A130013-

I4RS0B130015-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Бренд: DANA Страницы: 42
dallara F305 Manual preview
F305
Бренд: dallara Страницы: 37
Yakima BOA Installation Instructions Manual preview
BOA
Бренд: Yakima Страницы: 8
Uebler F42 Mounting And Operating Instructions preview
F42
Бренд: Uebler Страницы: 18
Triumph MAYFLOWER 1951 Instruction Book preview
MAYFLOWER 1951
Бренд: Triumph Страницы: 86
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Бренд: PUTCO Страницы: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Бренд: Westfalia Страницы: 18
IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Бренд: IBASE Technology Страницы: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Бренд: Modifry Products Страницы: 2
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Бренд: Waeco Страницы: 172
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Бренд: Renault Страницы: 183
Gator HUDGPS1 Quick Start Manual preview
HUDGPS1
Бренд: Gator Страницы: 2
Volvo 1996 960 Quick Tips preview
1996 960
Бренд: Volvo Страницы: 10
Reese Explore 63153 Instruction Manual preview
63153
Бренд: Reese Explore Страницы: 9
Honda 2007 Fit User Information preview
2007 Fit
Бренд: Honda Страницы: 24
Conrad 85 51 49 Operating Instructions Manual preview
85 51 49
Бренд: Conrad Страницы: 50
Curt Group 60638 Installation Manual preview
60638
Бренд: Curt Group Страницы: 3
Juna JRDAB-03 Installation Manual preview
JRDAB-03
Бренд: Juna Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды