manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Lighting Systems:  9B-6

Headlight Bulb Replacement

S4RS0A9206002

WARNING:

• To avoid danger of being burned, don’t 

touch when the bulb is hot.

• Don’t touch glass surface of bulb, to avoid 

deteriorate as the case may be unclear 
when bulb light on at dirty condition.

 

1) Disconnect negative (–) cable at battery.
2) Disconnect coupler from bulb.
3) Remove socket cover (1).
4) Replace bulb (2) and assemble all removed parts.

Headlight Aiming Adjustment with Screen

S4RS0A9206003

NOTE:

• Unless otherwise obligated by local regulations, adjust headlight aiming according to the following 

procedure.

• After replacing headlight housing, be sure to adjust aiming.

 

1) Make sure the following items.

• Place vehicle on a flat surface in front of blank wall (screen) (1) ahead of headlight surface.

Distance “a”
10 m (32.8 ft.)

• Adjust air pressure of all tires to the specified value respectively.
• Bounce vehicle body up and down by hand to stabilize suspension.
• Carry out aiming with a driver aboard.

Driver’s weight
75 kg (165 lb)

2) Check to see if hot spot (high intensity zone) of each low beam axis falls as shown in figure.

Hot spot specification
Angle “b”: 0.75

q

 (Specification)

Calculated distance “H”: Approx. 130 mm (5.15 in.)

1

iii)

2

i)

ii)

I4RS0A920005-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Qube AP1 Supplemental Instructions preview
AP1
Бренд: Qube Страницы: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Бренд: Cadillac Страницы: 32
JETBAG 320 Fitting Instructions Manual preview
320
Бренд: JETBAG Страницы: 44
Jeep 2014 Wrangler Owner'S Manual preview
2014 Wrangler
Бренд: Jeep Страницы: 673
GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Бренд: GMC Страницы: 20
Kolpin 25-9250 Owner'S And Operator'S Manual preview
25-9250
Бренд: Kolpin Страницы: 25
APEXi V-AFC II Instruction Manual preview
V-AFC II
Бренд: APEXi Страницы: 18
Prorack K519 Fitting Instructions For Basic Carrier preview
K519
Бренд: Prorack Страницы: 15
Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Бренд: Monacor Страницы: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Бренд: Jeep Страницы: 338
Toyota AURION 2013 Owner'S Manual preview
AURION 2013
Бренд: Toyota Страницы: 371
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Бренд: RAM Страницы: 174
Kuda 079020 Installation Instruction preview
079020
Бренд: Kuda Страницы: 2
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Бренд: Mobility Networks Страницы: 52
Jaeger 21360508 Fitting Instructions Manual preview
21360508
Бренд: Jaeger Страницы: 13
Saab 9000 1985 Service Manual preview
9000 1985
Бренд: Saab Страницы: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Бренд: A-rival Страницы: 23
WATT CARWATT CV12-220C150 User Manual preview
CARWATT CV12-220C150
Бренд: WATT Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды