manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

2B-6 Front Suspension: 

• Tighten wheel nuts to specified torque.

Tightening torque
Wheel nut:  85 N·m (8.5 kg-m, 61.5 lb-ft)

• After installation, confirm front wheel alignment.

Front Strut Assembly Disassembly and 
Assembly

S4RS0A2206007

Disassembly

1) With special tool (A) placed to spring as shown, turn 

special tool bolts alternately until spring tension is 
released. Whether it is released or not can be known 
by whether strut turns lightly while strut spring is held 
stationary.

Special tool
(A):  09940-71431

WARNING:

Use a commercially available spring 
compressor and follow the operation 
procedure described in the Instruction 
Manual supplied with that spring 
compressor.

 

2) While keeping spring compressed with special tool 

as shown, remove strut support lower nut.

Special tool
(B):  09900-00411 (socket)
(C):  09900-00414 (6 mm)

3) Disassemble strut assembly.

Assembly

For assembly, reverse disassembly procedure, noting 
the following instructions.

1) Compress spring with special tool (A) until total 

length becomes about 280 mm (11.0 in.) as shown.

Length
 280 mm (11.0 in.)

(d)

(a)

(b)

(c)

I4RS0A220008-

U: Upper side (small dia.)

L: Lower side (large dia.)

I4RS0A220009-

(B)

(C)

I4RS0A220007-

I4RS0A220010-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

LaserTrack Flare Installation Manual preview
Flare
Бренд: LaserTrack Страницы: 12
JASTEC von-S2 Instruction Manual preview
von-S2
Бренд: JASTEC Страницы: 12
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Бренд: Atwood Страницы: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Бренд: BMW Страницы: 21
DAF PACCAR PACMOBILE 20 User Manual preview
PACCAR PACMOBILE 20
Бренд: DAF Страницы: 18
Thule 1430 Kit Instructions Manual preview
1430 Kit
Бренд: Thule Страницы: 8
Sumitomo Dunlop L.D02.C.M Installation Manual preview
Dunlop L.D02.C.M
Бренд: Sumitomo Страницы: 22
Safe Fleet Prime Design OCM-3032 Quick Start Manual preview
Prime Design OCM-3032
Бренд: Safe Fleet Страницы: 4
Whispbar K482W Fitting Instructions Manual preview
K482W
Бренд: Whispbar Страницы: 14
Volvo Ski box Installation Instructions Manual preview
Ski box
Бренд: Volvo Страницы: 7
Quadratec 506-Rock Quick Start Quide preview
506-Rock
Бренд: Quadratec Страницы: 2
Ranger design C24-DL Installation Manual preview
C24-DL
Бренд: Ranger design Страницы: 14
Classic Accessories 80-485-142401-RT Instructions Manual preview
80-485-142401-RT
Бренд: Classic Accessories Страницы: 14
Havis PT-A-502 Install Instructions preview
PT-A-502
Бренд: Havis Страницы: 4
Chevrolet El Camino 1983 Owner'S Manual preview
El Camino 1983
Бренд: Chevrolet Страницы: 103
Peak PKC0BJ Owner'S Manual preview
PKC0BJ
Бренд: Peak Страницы: 8
Renault Kangoo Manual preview
Kangoo
Бренд: Renault Страницы: 239
Jaeger-leCoultre 21500632 Fitting Instructions Manual preview
21500632
Бренд: Jaeger-leCoultre Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды