manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-151

Tightening torque
Manual detent spring bolt (a):  10 N·m (1.0 kg-m, 
7.5 lb-ft)

3) Install parking lock pawl rod (2) to manual valve lever 

(1).

4) After applying A/T fluid to new manual valve lever 

(1), install new manual shift shaft (4), new spacer (3) 
and manual valve lever to transaxle case.

5) After installing manual valve lever pin (2) by using 

spring pin remover with 3 mm (0.12 in.) in diameter 
(5) and hammer, turn spacer to set the position as 
shown in figure. Then caulk spacer with a punch.

6) Install parking lock pawl bracket (1) to transaxle 

case.

Tightening torque
Parking lock pawl bracket bolt (a):  7.5 N·m (0.75 
kg-m, 5.5 lb-ft)

7) After applying A/T fluid to new O-rings, install them 

to 1st and reverse brake piston (3).

8) Install 1st and reverse brake piston (1) to transaxle 

case (2).

NOTE:
Be careful not to damage O-ring when 
installing 1st and reverse brake piston.

 

I2RH0B510259-

I2RH0B510260-

I2RH0B510261-

1. Inner O-ring

2. Outer O-ring

I2RH0B510262-

I2RH0B510263-

I2RH0B510264-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Carcomm CNM-71 Quick Start Manual preview
CNM-71
Бренд: Carcomm Страницы: 2
Whispbar K392W Fitting Instructions For Basic Carrier preview
K392W
Бренд: Whispbar Страницы: 14
GMC SIERRA 2002 Manual preview
SIERRA 2002
Бренд: GMC Страницы: 499
Kia Amanti Owner'S Manual preview
Amanti
Бренд: Kia Страницы: 290
Hama 00201510 Operating Instructions Manual preview
00201510
Бренд: Hama Страницы: 40
Cadillac 2007 CTS Owner'S Manual preview
2007 CTS
Бренд: Cadillac Страницы: 518
Opel OPEL INSIGNIA Infotainment Manual preview
OPEL INSIGNIA
Бренд: Opel Страницы: 141
Quadratec 12226.3011 Installation Manual preview
12226.3011
Бренд: Quadratec Страницы: 8
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Бренд: Chevrolet Страницы: 412
Thetford SANICON TURBO 300 Operating Instructions Manual preview
SANICON TURBO 300
Бренд: Thetford Страницы: 25
Quadratec 11113.1435 Quick Start Manual preview
11113.1435
Бренд: Quadratec Страницы: 14
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Бренд: N-Com Страницы: 36
Safe Fleet Prime Design VBI-FT31B Assembly Instructions Manual preview
Prime Design VBI-FT31B
Бренд: Safe Fleet Страницы: 12
Jaeger 21260514J Fitting Instructions Manual preview
21260514J
Бренд: Jaeger Страницы: 11
ATS 664-0030 Installation And Operating Manual preview
664-0030
Бренд: ATS Страницы: 12
Lund Tonno Pro Installation Instructions Manual preview
Tonno Pro
Бренд: Lund Страницы: 12
iSimple blustream Owner'S Manual preview
blustream
Бренд: iSimple Страницы: 12
ROLEC WallPod Series Installation Instructions preview
WallPod Series
Бренд: ROLEC Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды