manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-46 Automatic Transmission: 

Table for Step 4

3

Check transmission range sensor (switch) circuit for 
operation

Check by using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch 

OFF.

2) Turn ignition switch ON and check transmission range 

signal (P, R, N, D, 2 or L) on display when shifting select 
lever to each range.

Is applicable range indicated?

Intermittent trouble.
Check for intermittent 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00”.

Go to Step 5.

4

Check transmission range sensor (switch) circuit for 
operation

Check by not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals “C35-1”, “C35-7”, “C35-8”, 

“C35-18”, “C35-19” and “C35-20” respectively with 
select lever shifted to each range.
Taking terminal “C35-19” as an example, is battery 
voltage indicated only when select lever is shifted to “2” 
range and 0 V for other ranges as shown in the following 
table.
Check voltage at other terminals likewise, referring to the 
following table.

Are check results satisfactory?

Intermittent trouble.
Check for intermittent 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00”.

Go to Step 5.

5

1) Check select cable for adjustment referring to “Select 

Cable Adjustment: ”.

Is it adjusted correctly?

Go to Step 6.

Adjust.

6

Check transmission range sensor for installation 
position

1) Shift select lever to “N” range.
2) Check that “N” reference line on sensor and needle 

direction shaped on lock washer are aligned.

Are they aligned?

Go to Step 7.

Adjust.

7

1) Check transmission range sensor (switch) referring to 

“Transmission Range Sensor (Shift Switch) Inspection 
and Adjustment: ”.

Are check results satisfactory?

“RED/BLK”, “PNK/BLK”, 
“RED”, “GRN/ORN”, 
“GRN”, “GRN/YEL” or 
“LT GRN/BLK” circuit 
open or short to ground. 
If wires and connections 
are OK, substitute a 
know-good TCM and 
recheck.

Replace transmission 
range sensor.

Step

Action

Yes

No

Terminal

C35-20

C35-1

C35-8

C35-7

C35-19

C35-18

Select lever 
position

P

8 – 14 V

0 V

0 V

0 V

0 V

0 V

R

0 V

8 – 14 V

0 V

0 V

0 V

0 V

N

0 V

0 V

8 – 14 V

0 V

0 V

0 V

D or 3

0 V

0 V

0 V

8 – 14 V

0 V

0 V

2

0 V

0 V

0 V

0 V

8 – 14 V

0 V

L

0 V

0 V

0 V

0 V

0 V

8 – 14 V

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Westin 23-3130 Instructions preview
23-3130
Бренд: Westin Страницы: 3
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Бренд: Porsche Страницы: 144
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Бренд: GOgroove Страницы: 9
Mazda 2012 Mazda6 Owner'S Manual preview
2012 Mazda6
Бренд: Mazda Страницы: 527
Cadillac 2008 Escalade EXT Owner'S Manual preview
2008 Escalade EXT
Бренд: Cadillac Страницы: 496
Daewoo RACER 1998 Electrical Wiring Diagram preview
RACER 1998
Бренд: Daewoo Страницы: 68
Hyundai Getz 2004 Owner'S Manual preview
Getz 2004
Бренд: Hyundai Страницы: 437
Farad BARS PR25 - 2 Quick Start Manual preview
BARS PR25 - 2
Бренд: Farad Страницы: 8
Edelbrock For 1985-1992 GM Cars and Trucks 17933 Installation Instructions preview
For 1985-1992 GM Cars and Trucks 17933
Бренд: Edelbrock Страницы: 4
Prorack K748 Fitting Instructions Manual preview
K748
Бренд: Prorack Страницы: 14
Yakima K674 Instructions Manual preview
K674
Бренд: Yakima Страницы: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Бренд: Menabo Страницы: 11
Yakima K614 Manual preview
K614
Бренд: Yakima Страницы: 12
FALCON RIDGE CF-1000-WD05 Instructions For Installation And Care preview
CF-1000-WD05
Бренд: FALCON RIDGE Страницы: 6
Axxess AXRC-CH1 Installation Instructions Manual preview
AXRC-CH1
Бренд: Axxess Страницы: 8
Dodge Charger 1973 Body Service Manual preview
Charger 1973
Бренд: Dodge Страницы: 276
Camoplast T4S Installation Manuallines preview
T4S
Бренд: Camoplast Страницы: 19
Fisher Body FOLDING TOP 1971 Service Manual preview
FOLDING TOP 1971
Бренд: Fisher Body Страницы: 37

Бренды по названию

Популярные бренды

Загрузить еще бренды