manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

9D-5 Wipers / Washers: 

• For motor operation in high speed

a. Connect battery positive (+) terminal to “2” 

and its negative (–) terminal to terminal “5”.

b. Check if motor revolution speed is as 

specification. If check result is not as 
specified, replace motor.

Specification
60 – 76 r/min (rpm)

• For automatic stop operation

a. Connect battery positive (+) terminal to 

terminal “1” and its negative (–) terminal to 
terminal “5” and let the motor turn.

b. Disconnect terminal “1” from battery positive 

(+) terminal, and let the motor stop.

c. Connect terminals “1” and “3” with a jumper 

wire, and connect terminal “4” to battery 
positive (+) terminal.
Observe the motor turns once again then 
stops at a specified position as shown.

d. Repeat Step 1) to 3) several times and check 

that the motor stops at the specified position 
every time.
If check result is not satisfied, replace motor.

Rear Wiper (If Equipped) Removal and 
Installation

S4RS0A9406013

Removal

1) Disconnect negative (–) cable at battery.
2) Remove arm cover (1), rear wiper arm nut (2), rear 

wiper arm with blade assembly (3), rear wiper pivot 
cap (4), rear wiper nut (5) and rear wiper seal (6).

3) Remove rear end door trim referring to “Rear End 

Door Lock Assembly Removal and Installation:  in 
Section 9F”.

4) Disconnect coupler from rear wiper motor.
5) Remove rear wiper motor.

1

5

I4RS0A940010-

2

5

I4RS0A940011-

2. Windshield wiper arms with wiper blades
6. Ceramic line
7. Wiper blade center

4

5

3

1

6

6

7

2

2

I4RS0A940012-

1

2

3

4

5

6

I4RS0A940013-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Daihatsu TERIOS J100 Maintenance Manual preview
TERIOS J100
Бренд: Daihatsu Страницы: 43
Jeep Commander Overview Manual preview
Commander
Бренд: Jeep Страницы: 25
Jeep Commander Warranty Information Booklet preview
Commander
Бренд: Jeep Страницы: 51
Farenheit CCD-5XS Owner'S Manual preview
CCD-5XS
Бренд: Farenheit Страницы: 8
Jeep 2011 grand cherokee Accessories Quick Reference Manual preview
2011 grand cherokee
Бренд: Jeep Страницы: 22
Jeep 2013 Grand Cherokee Owner'S Manual preview
2013 Grand Cherokee
Бренд: Jeep Страницы: 704
Jeep 2012 Liberty Owner'S Manual preview
2012 Liberty
Бренд: Jeep Страницы: 558
Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Бренд: Monacor Страницы: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Бренд: Jeep Страницы: 338
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Бренд: KRAFTWERK Страницы: 2
Voxoa MCU-20A(P40) User Manual preview
MCU-20A(P40)
Бренд: Voxoa Страницы: 48
KEKO K617 Installation Description preview
K617
Бренд: KEKO Страницы: 3
Movon MDAS-5 Installation Manual preview
MDAS-5
Бренд: Movon Страницы: 43
Atera 080 705 User Information preview
080 705
Бренд: Atera Страницы: 3
Black Horse RB001BK Installation Instructions preview
RB001BK
Бренд: Black Horse Страницы: 5
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Бренд: Saturn Страницы: 440
iDataLink ADS-TBSL-GM Install Manual preview
ADS-TBSL-GM
Бренд: iDataLink Страницы: 6
Honda 2009 S2000 Owner'S Manual preview
2009 S2000
Бренд: Honda Страницы: 268

Бренды по названию

Популярные бренды

Загрузить еще бренды