manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

3A-3 Drive Shaft / Axle: 

Front Drive Shaft Assembly On-Vehicle 
Inspection

S4RS0A3106002

• Check boots for breakage or deterioration.
• Check wheel side joint for rattle or smooth rotation.
• Check differential side (or center shaft side) joint for 

smooth rotation.
If any abnormality is found, replace.

Front Drive Shaft Assembly Removal and 
Installation

S4RS0A3106003

Removal

1) Undo caulking (1) and remove drive shaft nut (2).

2) Remove wheel.
3) Drain transaxle oil referring to “Manual Transaxle Oil 

Change:  in Section 5B” or “A/T Fluid Change:  in 
Section 5A”.

4) Disconnect tie-rod end (1) from steering knuckle (2) 

using puller (3).

5) Remove stabilizer joint referring to “Front 

Suspension Frame, Stabilizer Bar and/or Bushings 
Removal and Installation:  in Section 2B”.

6) Remove brake hose mounting bolt.
7) Remove wheel speed sensor and suspension 

control arm ball joint bolt (1).

8) Disconnect front suspension control arm ball joint 

stud from steering knuckle.

9) Pull out drive shaft joint (2) as follows.

• For left side shaft:

Using tire lever (1), pull out drive shaft joint (2) so 
as to release snap ring fitting of joint spline at 
differential side.

• For right side shaft:

Using plastic hammer (3), drive out drive shaft 
joint (2) so as to release snap ring fitting of joint 
spline at center shaft.

1. Circlip

13. Center bearing

2. Differential side joint (Constant velocity tripod joint)

: Apply dark gray grease included in spare part to joint.

14. Center shaft

 3. Snap ring

15. Tripod joint spider

4. Boot band (Large)

16. Drive shaft nut

5. Boot (Differential or center shaft side)

17. Center bearing support bolt

6. Boot band (Small)

: 175 N

˜

m (17.5 kg-m, 126.5 lb-ft)

7. Boot (Wheel side)

: 55 N

˜

m (5.5 kg-m, 40.0 lb-ft)

8. Wheel side joint (Constant velocity ball joint)

: Apply black grease included in spare part to joint.

: Do not reuse.

I4RS0A310003-

I3RM0A310003-

[A]: Left side
[B]: Right side

1

I4RS0A310004-

I4RS0A310005-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Camcar 40052 Mounting Instructions preview
40052
Бренд: Camcar Страницы: 6
Pacbrake C44059 Installation Manual preview
C44059
Бренд: Pacbrake Страницы: 14
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
Streetwize LeisureWize EMOVE EM303A Manual preview
LeisureWize EMOVE EM303A
Бренд: Streetwize Страницы: 20
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Бренд: Mercedes-Benz Страницы: 373
BMW 01 29 9 416 497 Installation Instructions preview
01 29 9 416 497
Бренд: BMW Страницы: 5
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Бренд: muth Страницы: 9
Yakima StickUp Installation Instructions Manual preview
StickUp
Бренд: Yakima Страницы: 21
Mini COOPER Owner'S Manual preview
COOPER
Бренд: Mini Страницы: 20
Right Weigh 221-SK Installation Manual preview
221-SK
Бренд: Right Weigh Страницы: 16
Whispbar K919W Fitting Instructions Manual preview
K919W
Бренд: Whispbar Страницы: 17
Volvo 164 1969 Service Manual preview
164 1969
Бренд: Volvo Страницы: 266
RAM Truck 2014 Owner'S Manual preview
Truck 2014
Бренд: RAM Страницы: 330
RAM Promaster 2016 User Manual preview
Promaster 2016
Бренд: RAM Страницы: 148
Hamron 619-626 User Instructions preview
619-626
Бренд: Hamron Страницы: 36
Cadillac Escalade 2004 Escalade ESV Owner'S Manual preview
Escalade 2004 Escalade ESV
Бренд: Cadillac Страницы: 472
Toyota Tacoma 05 Brochure & Specs preview
Tacoma 05
Бренд: Toyota Страницы: 26
Subaru 1999 Legacy Owner'S Manual preview
1999 Legacy
Бренд: Subaru Страницы: 399

Бренды по названию

Популярные бренды

Загрузить еще бренды