Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 894 | Manualshive

Страница: 894 / 1257

background image

8B-24 Air Bag System:

DTC Troubleshooting

NOTE:
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Repeat “Air Bag Diagnostic System Check: ” to confirm that the trouble has been corrected.
• Clear DTCs of BCM referring to “DTC Clearance: in Section 10B”

DTC B1026: Pretensioner Activated

S4RS0A8204070

DTC Will Set when

The SDM detects a frontal crash of sufficient force to warrant activation of the pretensioner. (SDM outputs a
deployment command.)

Flow Test Description
Step 1:

Check that DTC B1026 has been set although pretensioner has not been activated.

Step 2:

Check that DTC has been set due to failure of SDM.

NOTE:
Before executing items in this flow, be sure to perform “Air Bag Diagnostic System Check: ”.

DTC Troubleshooting

NOTE:
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Repeat “Air Bag Diagnostic System Check: ” to confirm that the trouble has been corrected.
• Clear DTCs of BCM referring to “DTC Clearance: in Section 10B”

Step

Action

Yes

No

1

1) Turn ignition switch OFF.

Has air bag deployed?

Replace components
and perform inspections
as directed in “Repair
and Inspection
Required after Accident:
”.

Go to Step 2.

2

1) Inspect front of vehicle and undercarriage for signs of

impact.

Are there signs of impact?

Replace components
and perform inspections
as directed in “Repair
and Inspection
Required after Accident:
”.

Substitute a known-
good SDM and recheck.

Step

Action

Yes

No

1

1) Turn ignition switch OFF.

Has pretensioner activated?

Replace components
and perform inspections
as directed in “Repair
and Inspection
Required after Accident:
”.

Go to Step 2.

2

1) Inspect front of vehicle and undercarriage for signs of

impact.

Are there signs of impact?

Replace components
and perform inspections
as directed in “Repair
and Inspection
Required after Accident:
”.

Substitute a known-
good SDM and recheck.

«
...
892
893
894
895
896
...
»

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Бренд: AA Products Страницы: 8

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Volvo Страницы: 188

Бренд: Wilco Offroad Страницы: 4

Бренд: BMW Страницы: 21

Бренд: STARLANE Страницы: 24

Бренд: Westin Страницы: 3

Бренд: Guidosimplex Страницы: 8

PRIME DESIGN HXR-269-E-UM3-80

Бренд: Safe Fleet Страницы: 12

S90 - ACCESSORY PANEL

Бренд: Volvo Страницы: 166

Бренд: TrailFX Страницы: 2

Aura Mobile BT MCP-2014

Бренд: Spracht Страницы: 2

10-8002-C12167A

Бренд: Saleen Страницы: 6

Бренд: Hellwig Страницы: 5

Бренд: NavLinkz Страницы: 26

Бренд: v.link Страницы: 15

Countryman Cooper S

Бренд: Mini Страницы: 244

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды