manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

4E-21 ABS: 

DTC C1057: Power Source Circuit

S4RS0A4504017

Wiring Diagram

DTC Detecting Condition

The ABS control module monitors the power source voltage at terminal “E03-14”. When the power source voltage 
becomes extremely high or low while vehicle is running at more than 20 km/h (13 MPH), this DTC will be set. As soon 
as the power source voltage becomes normal, the ABS warning lamp will be turned off and the ABS control module 
will return to normal operation, but the set DTC will be remain.

DTC Troubleshooting

I4RS0A450016-

[A]: ABS hydraulic unit / control module connector E03

2. Main fuse box

1. Battery

3. ABS hydraulic unit / control module assembly

Step

Action

Yes

No

1

Was “ABS Check” performed?

Go to Step 2.

Go to “ABS Check: ”.

2

1) Disconnect ABS hydraulic unit / control module 

connector with ignition switch turned OFF.

2) Check for proper connection to ABS hydraulic unit / 

control module connector at terminals “E03-14” and 
“E03-13”.

3) If OK, then turn ignition switch to ON position and 

measure voltage between terminals “E03-14” and “E03-
13”. 

Is voltage 9.7 

r

 0.3 V or more?

Go to Step 5.

Go to Step 3.

3

1) Turn ignition switch to OFF.
2) Check for proper connection to ABS hydraulic unit / 

control module connector at terminals “E03-13” and 
“E03-26”.

3) If OK then turn ignition switch to ON and measure 

resistance between each terminal of “E03-13” and “E03-
26” and vehicle body ground.

Is resistance less than 2 

:

?

Go to Step 4.

“BLK” wire circuit in 
open or high resistance.

4

1) Measure voltage between positive battery terminal and 

vehicle body ground with engine running.

Is voltage 9.7 

r

 0.3 V or more?

Imperfect short between 
“WHT/BLU” wire circuit 
and body ground.

Check charging system 
referring to “Generator 
Test (Undercharged 
Battery Check):  in 
Section 1J”.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Daihatsu G200 Service Manual preview
G200
Бренд: Daihatsu Страницы: 485
Jeep Compass Overview Manual preview
Compass
Бренд: Jeep Страницы: 25
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Бренд: Haibang Страницы: 6
Tessera4x4 SOT-1311 ROLL Installation Manual preview
SOT-1311 ROLL
Бренд: Tessera4x4 Страницы: 20
Prorack WHISPBAR S53 Fitting Instructions For Basic Carrier preview
WHISPBAR S53
Бренд: Prorack Страницы: 10
Cadillac Fleetwood Brougham Sedan 1966 Owner'S Manual preview
Fleetwood Brougham Sedan 1966
Бренд: Cadillac Страницы: 56
POOL-LINE 110050 Assembly Instructions preview
110050
Бренд: POOL-LINE Страницы: 2
Ford TRANSIT CUSTOM Quick Reference Manual preview
TRANSIT CUSTOM
Бренд: Ford Страницы: 15
Honda 08L04-SZA-100 Installation Instructions preview
08L04-SZA-100
Бренд: Honda Страницы: 3
Belkin TuneBase F8Z442 User Manual preview
TuneBase F8Z442
Бренд: Belkin Страницы: 162
Waeco MagicSafe MSG150 Installation And Operating Manua preview
MagicSafe MSG150
Бренд: Waeco Страницы: 20
Honda 2000 Accord Sedan Online Reference Owner'S Manual preview
2000 Accord Sedan
Бренд: Honda Страницы: 320
Roadefend RDT401P Instruction Book preview
RDT401P
Бренд: Roadefend Страницы: 15
VDO VIEWLINE TEMPERATURE GAUGES Product Information preview
VIEWLINE TEMPERATURE GAUGES
Бренд: VDO Страницы: 5
Bestop 51719 Installation Instructions Manual preview
51719
Бренд: Bestop Страницы: 14
Yakima Prorack K370 Fitting Instructions Manual preview
Prorack K370
Бренд: Yakima Страницы: 14
Pacbrake P39106 Installation preview
P39106
Бренд: Pacbrake Страницы: 2
Geely EX7 Warranty And Maintenance Manual preview
EX7
Бренд: Geely Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды