manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

4C-7 Rear Brakes: 

Installation

1) Install brake back plate (1) and spindle (2), and 

tighten spindle bolts (3) by hand.

2) Install rear wheel speed sensor (1) to brake back 

plate (2).

Tightening torque
Rear wheel speed sensor bolt (a):  11 N·m (1.1 
kg-m, 8.0 lb-ft)

3) Tighten spindle bolts (b) to specified torque.

Tightening torque
Spindle bolt (b):  73 N·m (7.3 kg-m, 53.0 lb-ft)

4) Install parking brake cable (1) to brake back plate

Tightening torque
Parking cable cap nut (a):  10 N·m (1.0 kg-m, 7.5 
lb-ft)

5) Install wheel cylinder and connect brake pipe flare 

nut, and then tighten wheel cylinder bolts and flare 
nut to specified torque referring to “Wheel Cylinder 
Removal and Installation: ”. 

6) Install brake shoe referring to “Rear Brake Shoe 

Removal and Installation: ”.

7) Install brake drum referring to step 2) to 7) of “Rear 

Brake Drum Removal and Installation: ”.

8) Fill reservoir with brake fluid and bleed brake 

system. For bleeding operation refer to “Air Bleeding 
of Brake System:  in Section 4A”.

9) Upon completion of all jobs, depress brake pedal 

with about 300 N (30 kg, 66 lbs) load 3 to 5 times so 
as to obtain proper drum-to-shoe clearance.
Adjust parking brake cable.

Tightening torque
Wheel nut (a):  85 N·m (8.5 kg-m, 61.5 lb-ft)

10) Check to ensure that brake drum is free from 

dragging and proper braking is obtained. Then 
remove vehicle from hoist and perform brake test 
(foot brake and parking brake).

11) Check each installed part for fluid leakage.

1

2

3

I4RS0A430022-

(a)

(b)

2

1

I4RS0A430023-

1

(a)

I4RS0A430024-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Бренд: Lincoln Страницы: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Бренд: Volkswagen Страницы: 26
Quadratec Brute Strength 12057.0271 Installation Manual preview
Brute Strength 12057.0271
Бренд: Quadratec Страницы: 6
Dometic GROUP DRS2 Installation And Operating Manual preview
DRS2
Бренд: Dometic GROUP Страницы: 20
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Бренд: Blue Giant Страницы: 48
Tessera4x4 SOT-1311 ROLL Installation Manual preview
SOT-1311 ROLL
Бренд: Tessera4x4 Страницы: 20
VDO VIEWLINE 52 MM - MOUNTING 11-09 Installation Instructions preview
VIEWLINE 52 MM - MOUNTING 11-09
Бренд: VDO Страницы: 4
Kuda 079020 Installation Instruction preview
079020
Бренд: Kuda Страницы: 2
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Бренд: Thule Страницы: 12
Calix group TYP MVP 823 Assembly Instructions preview
TYP MVP 823
Бренд: Calix group Страницы: 4
Metra Electronics 99-5026 Installation Instructions Manual preview
99-5026
Бренд: Metra Electronics Страницы: 20
Mazda 3 Facelift 2006 Training Manual preview
3 Facelift 2006
Бренд: Mazda Страницы: 94
Metra Electronics 99-9302 Installation Instructions Manual preview
99-9302
Бренд: Metra Electronics Страницы: 8
AEM 21-5011 Installation Manuallines preview
21-5011
Бренд: AEM Страницы: 5
CEMO DT-Mobil Easy 200 L Original Operating Instructions preview
DT-Mobil Easy 200 L
Бренд: CEMO Страницы: 80
GMC 2013 Terrain Owner'S Manual preview
2013 Terrain
Бренд: GMC Страницы: 364
DV8 LBBR-01 Installation Manual preview
LBBR-01
Бренд: DV8 Страницы: 5
PEUGEOT 208 Handbook preview
208
Бренд: PEUGEOT Страницы: 357

Бренды по названию

Популярные бренды

Загрузить еще бренды