Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 458 | Manualshive

Страница: 458 / 1257

background image

3A-5 Drive Shaft / Axle:

3) Remove tripod joint spider (1) using 3 arms puller

(2).

CAUTION:

To prevent any problem caused by washing
solution, do not wash tripod joint except its
housing. Degreasing of tripod joint with cloth
is allowed.

4) Remove differential side (or center shaft side) boot

small band, and then pull out differential side (or
center shaft side) boot from shaft.

5) Undo caulking (5) of wheel side boot big band (1)

and small band (3) using flat end rod (2) or the like,
then pull out wheel side boot (4) from shaft.

Assembly

Judging from abnormality noted before disassembly and
what is found through visual check of component parts
after disassembly, prepare replacing parts and proceed
to reassembly.
Make sure that wheel side joint assembly (1) and tripod
joint housing (2) are washed thoroughly and air dried.
Replace boot(s) (3) with new one(s).

CAUTION:

• Do not wash boots in degreaser such as

gasoline or kerosene. etc. Washing in
degreaser causes deterioration of boot.

• To ensure full performance of joint as

designed, be sure to distinguish between
two types of grease in repair set and apply
specified volume to respective joint
referring to the followings for identification
of the grease.

1) Wash disassembled parts (except boots). After

washing, dry parts completely by blowing air.

2) Clean boots with cloth.
3) Apply grease to wheel side joint. Use specified

grease in tube in wheel side boot set.

Grease color
: Black

Amount
: 55 – 75 g (1.9 – 2.6 oz)

4) Install wheel side boot on shaft.
5) Fill up boot inside with specified grease.
6) Place new wheel side boot big band (3) and small

band (4) onto boot putting band outer end (1) against
forward rotation (2) as shown in figure.

I3RH0A311004-

I4RS0A310006-

[A]: Wheel side
[B]: Differential side (or center shaft side)

I4RS0A310007-

I4RS0A310009-

«
...
456
457
458
459
460
...
»

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

AUDI 4G HIGHEND

Бренд: KAP Страницы: 20

Бренд: Prorack Страницы: 14

Бренд: Ford Страницы: 2

Бренд: NavLinkz Страницы: 21

Бренд: Harman Kardon Страницы: 16

Бренд: TATA Motors Страницы: 184

PW-50C Civilian

Бренд: B&G electronics Страницы: 7

Бренд: Ford Страницы: 256

Бренд: Subaru Страницы: 298

Security Cage Kit

Бренд: Toro Страницы: 8

Бренд: Oldsmobile Страницы: 358

Бренд: Kleinn Страницы: 8

Бренд: Magneti Marelli Страницы: 9

Бренд: Ford Страницы: 51

Бренд: Blue Ox Страницы: 9

Бренд: Nav TV Страницы: 11

Бренд: Curt Manufacturing Страницы: 4

Бренд: Menabo Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды