manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

9C-5 Instrumentation / Driver Info. / Horn: 

Low Fuel Warning Light Symptom Diagnosis

S4RS0A9304018

NOTE:

• Make sure that any DTC is not detected by ECM an before starting the troubleshooting by using the 

following table. If any DTC is detected, troubleshoot the DTC advance.

• Confirm that fuel meter is in good condition before referring to the following possible causes.

– When fuel level meter circuit is shorted to ground circuit, fuel level meter indicates empty and low 

fuel warning lamp comes ON even if fuel tank does not empty.

– The low fuel warning light comes ON when fuel level is lower than specification below.

 

Low fuel warning light operation:

Oil Pressure Warning Light Symptom Diagnosis

S4RS0A9304019

NOTE:
Make sure that any DTC is not detected by BCM before starting the troubleshooting by using the 
following table. If any DTC is detected, troubleshoot the DTC advance.

 

Low fuel warning 

light operation:

Fuel amount:

Resistance of fuel level sensor:

ON

Approx. 6.5 liter

Approx. 251 

:

Condition

Possible cause

Correction / Reference Item

Low fuel warning light 
does not come ON when 
fuel level is lower than 
specification

Circuit fuse blown

Replace fuse and check for short circuit.

Fuel level sensor faulty

Check fuel level sensor referring to “Fuel Level 
Sensor Inspection: ”.

Wiring or ground faulty

Repair circuit.

Combination meter faulty

Replace combination meter.

Low fuel warning light 
comes ON steady

Low fuel

Refill fuel.

Fuel level sensor faulty

Check fuel level sensor referring to “Fuel Level 
Sensor Inspection: ”.

Wiring or ground faulty

Repair circuit.

Combination meter faulty

Replace combination meter.

Condition

Possible cause

Correction / Reference Item

Oil pressure warning light 
does not light up when 
ignition switch is turned 
to ON position at engine 
off

Circuit fuse blown

Replace fuse and check for short circuit.

Oil pressure switch faulty

Check oil pressure switch referring to “Oil 
Pressure Switch Inspection: ”.

Wiring or ground faulty

Repair circuit.

Combination meter faulty

Replace combination meter.

Oil pressure warning light 
stays ON

Oil pressure switch faulty

Check oil pressure switch referring to “Oil 
Pressure Switch Inspection: ”.

Wiring or ground faulty

Repair circuit.

Combination meter faulty

Replace combination meter.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

ULTIMATE SPEED CARBON Assembly And Safety Advice preview
CARBON
Бренд: ULTIMATE SPEED Страницы: 19
Dakota Digital VHX-37F Installation preview
VHX-37F
Бренд: Dakota Digital Страницы: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Бренд: Dakota Digital Страницы: 7
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Бренд: Jeep Страницы: 108
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Бренд: Jeep Страницы: 6
Acura 2006 TSX Owner'S Manual preview
2006 TSX
Бренд: Acura Страницы: 2
TBC 645624 Instruction Manual preview
645624
Бренд: TBC Страницы: 12
Prorack K194 Fitting Instructions For Basic Carrier preview
K194
Бренд: Prorack Страницы: 14
WABCO Truck Training Model Operating Instructions Manual preview
Truck Training Model
Бренд: WABCO Страницы: 56
Vangear Woody-Pod Instruction Manual preview
Woody-Pod
Бренд: Vangear Страницы: 5
Safe Fleet FRC SafeTrack Hardware Installation Manual preview
FRC SafeTrack
Бренд: Safe Fleet Страницы: 20
Wagan Easy Air Auto Screen User Manual preview
Easy Air Auto Screen
Бренд: Wagan Страницы: 8
Voxx Electronics CA-510a Installation Instructions Manual preview
CA-510a
Бренд: Voxx Electronics Страницы: 15
Curt Manufacturing 58963 Installation Manual preview
58963
Бренд: Curt Manufacturing Страницы: 4
Whispbar K559W Fitting Instructions Manual preview
K559W
Бренд: Whispbar Страницы: 112
Mitsubishi 2015 OUTLANDER Owner'S Manual preview
2015 OUTLANDER
Бренд: Mitsubishi Страницы: 490
Smappee EVB-1332-BL-E Installation Manual preview
EVB-1332-BL-E
Бренд: Smappee Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды