Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 244

Страница: 244 / 1257

1A-196 Engine General Information and Diagnosis:

Step

Action

Yes

Is there DTC(s) of ECT sensor circuit (DTC P0116 / P0117 /
P0118) and/or radiator cooling fan circuit (DTC P0480)?

Go to corresponding
DTC flow.

Go to Step 2.

Low speed radiator cooling fan control circuit check

1) Connect scan tool to DLC with ignition switch turned

OFF.

2) Start engine and select “DATA LIST” mode on scan tool.
3) Warm up engine until coolant temp. is 97.5

C, 207.5

or higher and A/C switch turns OFF. (If engine coolant
temp. dose not rise, check engine cooling system or
ECT sensor.)

Is radiator cooling fan started at low speed when engine
coolant temp. reached above temp.?

Go to Step 3.

Perform from Step 2 to
Step 5 in “Radiator
cooling fan Low Speed
Control System Check:
”.

High speed radiator cooling fan control circuit check

1) Start engine and select “DATA LIST” mode on scan tool.
2) Warm up engine until coolant temp. is 102.5

C, 216.5

or higher and A/C switch turns OFF. (If engine coolant
temp. dose not rise, check engine cooling system or
ECT sensor.)

Is radiator cooling fan started at high speed when engine
coolant temp. reached above temp?

Radiator cooling fan
control system is in
good condition.

Perform from Step 9 to
Step 14 in DTC P0480
diag. flow.
If OK, Go to Step 4.

Radiator cooling fan control No. 2 and No. 3 check

1) Run engine when ECT is over 102.5

C, 216.5

2) Measure voltage between vehicle body ground and

“E23-48” terminal of ECM connector.

Is voltage lower than 1.5 V?

Go to Step 5.

Faulty ECM.

Radiator cooling fan No. 2 wire circuit check

1) Remove radiator cooling fan control relay No.2 with

ignition switch turned OFF.

2) Measure voltage between “GRY” wire terminal of

disconnected radiator cooling fan control relay No. 2
connector and vehicle body ground.

Is voltage 10 – 14 V?

Go to Step 6.

“GRY” wire is open or
high resistance circuit.

Radiator cooling fan No. 2 wire circuit check

1) Disconnect connector from radiator cooling fan motor

with ignition switch turned OFF.

2) Measure resistance between “BLU/BLK” wire terminal of

disconnected radiator cooling fan control relay No. 2
connector and vehicle body ground.

Is resistance infinity?

Go to Step 7.

“BLU/BLK” wire is
shorted to ground
circuit.

Radiator cooling fan No. 2 wire circuit check

1) Turn ON ignition switch.
2) Measure voltage between “BLU/BLK” wire terminal of

disconnected radiator cooling fan control relay No. 2
connector and vehicle body ground.

Is voltage 0 V?

Go to Step 8.

“BLU/BLK” wire is
shorted to power supply
circuit.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды