manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine Mechanical:  1D-40

Valve stem end deflection

If bore gauge is not available, check end deflection of 
valve stem with a dial gauge instead.
Move stem end in directions (1) and (2) to measure end 
deflection.
If deflection exceeds its limit, replace valve stem and 
valve guide.

Valve stem end deflection limit
In: 0.14 mm (0.005 in.)
Ex: 0.18 mm (0.007 in.)

Valve

Visual inspection

• Remove all carbon from valves.
• Inspect each valve for wear, burn or distortion at its 

face and stem end, as necessary, replace it.

• Inspect valve stem end face for pitting and wear. If 

pitting or wear is found there, valve stem end may be 
resurfaced, but not too much to grind off its chamber. 
When it is worn out too much that its chamber is gone, 
replace valve.

Valve head thickness

Measure thickness “a” of valve head. If measured 
thickness exceeds limit, replace valve.

Valve head thickness “a” (In and Ex)
Standard: 1.25 – 1.55 mm (0.049 – 0.061 in.)
Limit: 0.9 mm (0.035 in.)

I3RM0A140035-

IYSQ01141096-

I2RH01140135-

I2RH0B140102-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Бренд: Jacob Jensen Страницы: 28
GMC ANDROID INTERFACE Instruction Manual preview
ANDROID INTERFACE
Бренд: GMC Страницы: 18
Prorack K496 Fitting Instructions For Basic Carrier preview
K496
Бренд: Prorack Страницы: 15
Toyota AURION 2013 Owner'S Manual preview
AURION 2013
Бренд: Toyota Страницы: 371
Audi Q3 2015 - 2019 Technical Service Bulletin preview
Q3 2015 - 2019
Бренд: Audi Страницы: 12
CARRYBOY CB-796IG2-CIGD-R Installation Manual preview
CB-796IG2-CIGD-R
Бренд: CARRYBOY Страницы: 4
GMC 2012 Terrain Owner'S Manual preview
2012 Terrain
Бренд: GMC Страницы: 428
Subaru 2007 Impreza Brochure & Specs preview
2007 Impreza
Бренд: Subaru Страницы: 21
Saleen 10-8002-C11670C Manual preview
10-8002-C11670C
Бренд: Saleen Страницы: 17
RAM 2011 DAKOTA User Manual preview
2011 DAKOTA
Бренд: RAM Страницы: 76
Advantech TREK-550 Manual preview
TREK-550
Бренд: Advantech Страницы: 59
Waeco 8885100124 Operating Manual preview
8885100124
Бренд: Waeco Страницы: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Бренд: VBG Страницы: 16
TATA Motors Sumo Victa EX Owner'S Manual & Service Book preview
Sumo Victa EX
Бренд: TATA Motors Страницы: 92
Volvo S90 2018 Quick Manual preview
S90 2018
Бренд: Volvo Страницы: 42
ICON 91824E Installation Instructions preview
91824E
Бренд: ICON Страницы: 4
PEUGEOT BOXER 2018 Handbook preview
BOXER 2018
Бренд: PEUGEOT Страницы: 232
Acura 2011 RDX Navigation System Advanced Technology Manual preview
2011 RDX Navigation System
Бренд: Acura Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды