manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Hood / Fenders / Doors:  9J-7

Specifications

Tightening Torque Specifications

S4RS0A9A07001

NOTE:
The specified tightening torque is also described in the following.
“Front Door Assembly Components: ”
“Rear Door Assembly Components: ”
“Rear End Door Assembly Components: ”

 

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information:  in Section 0A”.

Special Tools and Equipment

Recommended Service Material

S4RS0A9A08001

NOTE:
Required service material is also described in the following.
“Front Door Assembly Components: ”
“Rear Door Assembly Components: ”
“Rear End Door Assembly Components: ”

 

Fastening part

Tightening torque

Note

N

˜

m

kg-m

lb-ft

Hood latch bolt

10

1.0

7.5

)

Door hinge mounting bolt (body side)

27

2.7

19.5

)

Door hinge mounting bolt (door side)

23

2.3

17.0

)

Door open stopper bolt

21

2.1

15.5

)

Rear end door balancer bolt

23

2.3

17.0

)

Material

SUZUKI recommended product or Specification

Note

Grease

SUZUKI Super Grease A

P/No.: 99000–25010

)

 / 

)

Sealant

SUZUKI Bond No.1215

P/No.: 99000–31110

)

 / 

)

 / 

)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Acdeos AXS FL Installation Instruction preview
AXS FL
Бренд: Acdeos Страницы: 7
Dodge Challenger 2013 Owner'S Manual preview
Challenger 2013
Бренд: Dodge Страницы: 543
ULTIMATE SPEED UAWSO 2 B1 Operation And Safety Notes preview
UAWSO 2 B1
Бренд: ULTIMATE SPEED Страницы: 32
Chevrolet 1998 Tahoe Manual preview
1998 Tahoe
Бренд: Chevrolet Страницы: 441
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Бренд: Mercedes-Benz Страницы: 91
Volvo 1989 780 Owner'S Manual preview
1989 780
Бренд: Volvo Страницы: 123
SSV Works RG4-DM3 Manual preview
RG4-DM3
Бренд: SSV Works Страницы: 2
Prorack K442 Fitting Instructions Manual preview
K442
Бренд: Prorack Страницы: 15
Buick 1997 Park Avenue Manual preview
1997 Park Avenue
Бренд: Buick Страницы: 420
Curt Manufacturing LIPPERT 18109 Installation Manual preview
LIPPERT 18109
Бренд: Curt Manufacturing Страницы: 3
Lancia DELTA HF integrale Workshop Manual preview
DELTA HF integrale
Бренд: Lancia Страницы: 101
Paser SKT 170 HYUNDAI Installation Manual preview
SKT 170 HYUNDAI
Бренд: Paser Страницы: 4
Yakima PR3041 Fitting Instructions Manual preview
PR3041
Бренд: Yakima Страницы: 13
70mai UP03 User Manual preview
UP03
Бренд: 70mai Страницы: 47
RAM PROMASTER 2018 User Manual preview
PROMASTER 2018
Бренд: RAM Страницы: 196
Blueant SUPERTOOTH 3 User Manual preview
SUPERTOOTH 3
Бренд: Blueant Страницы: 48
FORM FIT HD 5A 06 Quick Start Manual preview
HD 5A 06
Бренд: FORM FIT Страницы: 2
Mercedes-Benz 2001 C 240 Operator'S Manual preview
2001 C 240
Бренд: Mercedes-Benz Страницы: 381

Бренды по названию

Популярные бренды

Загрузить еще бренды