manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Instrumentation / Driver Info. / Horn:  9C-10

Remote Audio Control Switch (If Equipped) Symptom Diagnosis

S4RS0A9304014

Repair Instructions

Ignition Switch Removal and Installation

S4RS0A9306001

Removal

1) Disconnect negative cable at battery.
2) Confirm that ignition key is removed.
3) Remove steering column hole cover (1).
4) Turn steering wheel to remove steering column 

cover screws (3) and then remove steering column 
covers (2).

5) Disconnect couplers (1) from ignition switch (2).
6) Remove ignition switch (2) from key cylinder (3).

Installation

Reverse removal procedure.

Sound skips or is noisy

CD-ROM faulty

—

Driving vibration

—

Water droplets form on internal lens

Dry about 1 hour with power on.

Radio assembly installed incorrectly

Install correctly.

Radio assembly faulty

Replace radio assembly.

CD player is operative, 
but all speakers does not 
sound

Wiring and/or grounding faulty

Repair as necessary.

Radio assembly faulty

Replace radio assembly.

Individual speaker is 
noisy or inoperative

Wiring and/or grounding faulty

Repair as necessary.

Speaker faulty

Replace speaker.

Radio assembly faulty

Replace radio assembly.

Sound quality or volume 
is poor

CD-ROM faulty

—

Wiring and/or grounding faulty

Repair as necessary.

Speaker installed incorrectly

Install correctly.

Speaker faulty

Replace speaker.

Condition

Possible cause

Correction / Reference Item

Condition

Possible cause

Correction / Reference Item

Audio system is 
operative, but remote 
control switch does not 
control audio system

Remote audio control switch faulty

Check remote audio control switch referring to 
“Remote Audio Control Switch Inspection: ”.

Contact coil faulty

Replace contact coil.

Wiring and/or grounding faulty

Repair as necessary.

Radio assembly faulty

Replace radio assembly.

1

3

2

I4RS0A920007-

1

1

2

3

I4RS0A930008-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Ford FOCUS RS 2018 Owner'S Manual Supplement preview
FOCUS RS 2018
Бренд: Ford Страницы: 52
Whispbar K728W Fitting Instructions Manual preview
K728W
Бренд: Whispbar Страницы: 85
XTC ATS-POL-GBU Manual preview
ATS-POL-GBU
Бренд: XTC Страницы: 4
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Бренд: Lit Lightz Страницы: 3
Subaru 360 Sedan Service Manual preview
360 Sedan
Бренд: Subaru Страницы: 16
Metra Electronics 99-7860 Installation Instructions preview
99-7860
Бренд: Metra Electronics Страницы: 5
Renkforce RF-4743771 Operating Instructions preview
RF-4743771
Бренд: Renkforce Страницы: 4
JKS JKSOGS960 Installation Instructions Manual preview
JKSOGS960
Бренд: JKS Страницы: 6
Thule 1809 Instruction Manual preview
1809
Бренд: Thule Страницы: 4
Vauxhall Crossland X 2017 Owner'S Manual preview
Crossland X 2017
Бренд: Vauxhall Страницы: 245
J. Strong JST506BT Installation Instructions preview
JST506BT
Бренд: J. Strong Страницы: 2
Summit Racing SUM-G1083 Assembly & Use Instructions preview
SUM-G1083
Бренд: Summit Racing Страницы: 11
Menabo YELO 4 NS Fitting Instructions Manual preview
YELO 4 NS
Бренд: Menabo Страницы: 8
Ford 2003 Mustang Workshop Manual preview
2003 Mustang
Бренд: Ford Страницы: 4378
Toyota 2013 Prius c Owner'S Manual preview
2013 Prius c
Бренд: Toyota Страницы: 549
Black Horse Off Road TR-JECOOE Installation Instructions preview
TR-JECOOE
Бренд: Black Horse Off Road Страницы: 3
Mercedes-Benz SLK 350 Brochure preview
SLK 350
Бренд: Mercedes-Benz Страницы: 24
Connects2 CTQIAU03 Installation & User Manual preview
CTQIAU03
Бренд: Connects2 Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды