manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-57

DTC P0788: Shift / Timing Solenoid Control Circuit High

S4RS0A5104050

Wiring Diagram

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC in TCM memory.
3) Start engine and shift select lever to “N” range.
4) Repeat shifting select lever from “N” range to “D” range and vice versa for 3 times.
5) Check DTC.

DTC Troubleshooting

1. TCM

3. A/T

2. Timing solenoid valve

[A]: Terminal arrangement of TCM connector (viewed from harness side)

DTC detecting condition

Trouble area

Voltage of timing solenoid valve TCM terminal is high 
although TCM is commanding timing solenoid valve to turn 
OFF.

• Timing solenoid valve circuit open or shorted to 

power circuit

• Timing solenoid valve malfunction
• TCM

12V

C34-14

BLU/BLK

3

1

2

14

C34

C35

[A]

I4RS0A510014-

Step

Action

Yes

No

1

Was “A/T System Check” performed?

Go to Step 2.

Go to “A/T System 
Check: ”.

2

Check timing solenoid valve circuit for IG short

1) Disconnect TCM connectors.
2) Turn ignition switch ON and measure voltage between 

terminal “C34-14” of harness side TCM connector and 
ground.

Is it 0 – 1 V?

Go to Step 3.

“BLU/BLK” circuit 
shorted to power circuit.

3

Check timing solenoid valve circuit for open

1) Measure resistance between terminal “C34-14” of 

disconnected harness side TCM connector and ground.

Is it 11 – 15 

:

 at 20 

q

C (68 

q

F)?

Intermittent trouble or 
faulty TCM.
Check for intermittent 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00”.
If OK, substitute a 
known-good TCM and 
recheck.

Go to Step 4.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Samsung HF1000 User Manual preview
HF1000
Бренд: Samsung Страницы: 133
CAMPARK R10 Manual preview
R10
Бренд: CAMPARK Страницы: 20
RAM CHASSIS CAB 3500 2017 Quick Reference Manual preview
CHASSIS CAB 3500 2017
Бренд: RAM Страницы: 16
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Бренд: Haibang Страницы: 6
Cadillac 2007 CTS Owner'S Manual preview
2007 CTS
Бренд: Cadillac Страницы: 518
Opel OPEL INSIGNIA Infotainment Manual preview
OPEL INSIGNIA
Бренд: Opel Страницы: 141
TATA Motors tigor Owner'S Manual preview
tigor
Бренд: TATA Motors Страницы: 159
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Бренд: hc-cargo Страницы: 60
Fab Fours C3150 Installation Instructions Manual preview
C3150
Бренд: Fab Fours Страницы: 21
Metra Electronics 99-5026 Installation Instructions Manual preview
99-5026
Бренд: Metra Electronics Страницы: 20
Mazda 3 Facelift 2006 Training Manual preview
3 Facelift 2006
Бренд: Mazda Страницы: 94
Ford Fusion 2019 Supplement Manual preview
Fusion 2019
Бренд: Ford Страницы: 51
Honda 2010 Accord Coupe Owner'S Manual preview
2010 Accord Coupe
Бренд: Honda Страницы: 410
Menabo KIT+1 MERAK Fitting Instructions Manual preview
KIT+1 MERAK
Бренд: Menabo Страницы: 8
Curt Group Aries AL235045 Installation Manual preview
Aries AL235045
Бренд: Curt Group Страницы: 2
Phonocar 6/946 Instruction Manual preview
6/946
Бренд: Phonocar Страницы: 4
Oldsmobile ALERO 2001 Owner'S Manual preview
ALERO 2001
Бренд: Oldsmobile Страницы: 340

Бренды по названию

Популярные бренды

Загрузить еще бренды