Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 669

Страница: 669 / 1257

Automatic Transmission: 5A-129

Direct Clutch Assembly Inspection

S4RS0A5106033

Clutch Discs, Plates and Retaining Plate

Check that sliding surfaces of discs, separator plates
and retaining plate are not worn hard or burnt. If
necessary, replace.

NOTE:

• If disc lining is exfoliated, discolored,

replace all discs.

• Before assembling new discs, soak them

in A/T fluid for at least two hours.

Direct Clutch Return Spring Subassembly

Measure free length of direct clutch return spring.

Direct clutch return spring free length
“a”: 36.04 mm (1.419 in.)

NOTE:
Do not apply excessive force when
measuring spring free length. Perform
measurement at several points.

Direct Clutch Piston

Shake direct clutch piston lightly and check that check
ball (1) is not stuck.
Blow in low pressure air (Max. 100 kPa, 1 kg/cm

, 15 psi)

to check ball to check that there is no leakage.

I2RH0B510172-

I2RH0B510173-

I2RH0B510174-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды