Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 491

Страница: 491 / 1257

Front Brakes: 4B-8

Specifications

Tightening Torque Specifications

S4RS0A4207001

NOTE:
The specified tightening torque is also described in the following.
“Front Disc Brake Components: ”

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information: in Section 0A”.

Special Tools and Equipment

Recommended Service Material

S4RS0A4208001

NOTE:
Required service material is also described in the following.
“Front Disc Brake Components: ”

Special Tool

S4RS0A4208002

Fastening part

Tightening torque

Note

kg-m

lb-ft

Caliper pin bolt

2.6

19.0

)

Wheel nut

8.5

61.5

)

Flexible hose joint bolt

2.3

17.0

)

Bleeder plug

8.0

0.8

6.0

)

Caliper carrier bolt

8.5

61.5

)

09900–20607

09900–20701

Dial gauge

Magnetic stand

)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды