manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Immobilizer Control System:  10C-5

Diagnostic Information and Procedures

Immobilizer Control System Check

S4RS0AA304001

Diagnostic Trouble Code (DTC) Check

S4RS0AA304002

NOTE:
To know how to use SUZUKI scan tool in 
detail, refer to its operator’s manual.

 

1) Turn the ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector 

(DLC) (1) located under instrument panel at driver’s 
seat side.

Special tool
(A):  SUZUKI scan tool

3) Turn the ignition switch to ON position.
4) Check if any DTC is stored in ECM according to the 

instructions displayed on SUZUKI scan tool. 

5) After completing the check, turn ignition switch to 

OFF position, and then disconnect SUZUKI scan 
tool from DLC.

Diagnostic Trouble Code (DTC) Clearance

S4RS0AA304027

NOTE:
To know how to use SUZUKI scan tool in 
detail, refer to its operator’s manual.

 

1) Turn the ignition switch to OFF position,
2) Connect SUZUKI scan tool to data link connector 

(DLC) (1) located under instrument panel at driver’s 
seat side.

Special tool
(A):  SUZUKI scan tool

1) Turn the ignition switch to ON position.
2) Clear DTC(s) according to the instructions displayed 

on SUZUKI scan tool.

3) After completing the clearance, turn the ignition 

switch to OFF position, and then disconnect SUZUKI 
scan tool from DLC.

Step

Action

Yes

No

1

1) Start the engine.

Is it possible to start the engine?

Immobilizer control 
system is in good 
condition.

Go to Step 2.

2

1) Check behavior of immobilizer indicator lamp (1) by 

turning the ignition switch to ON position.

Does it flash ON and OFF continuously?

Check what diagnostic 
trouble code (DTC) is 
detected by ECM 
referring to “Diagnostic 
Trouble Code (DTC) 
Check: ”. Then, perform 
the troubleshooting 
referring to the 
corresponding flowchart 
in this section.

Perform “Engine and 
Emission Control 
System Check:  in 
Section 1A”.

1

I4RS0AA30004-

(A)

1

I4RS0AA30005-

(A)

1

I4RS0AA30005-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Бренд: DANA Страницы: 42
dallara F305 Manual preview
F305
Бренд: dallara Страницы: 37
Yakima BOA Installation Instructions Manual preview
BOA
Бренд: Yakima Страницы: 8
Parrot CK3300 Setup Information Manual preview
CK3300
Бренд: Parrot Страницы: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Бренд: Parrot Страницы: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Бренд: Parrot Страницы: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Бренд: Parrot Страницы: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Бренд: Parrot Страницы: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Бренд: Parrot Страницы: 106
Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Бренд: Lincoln Страницы: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Бренд: Volkswagen Страницы: 26
HUSKY LINERS X-ACT CONTOUR 53491 Care And Use Instructions preview
X-ACT CONTOUR 53491
Бренд: HUSKY LINERS Страницы: 2
Volvo 30728293 Installation Instructions Manual preview
30728293
Бренд: Volvo Страницы: 19
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Бренд: BrandMotion Страницы: 8
U & Me Brothers LK-168A Manual preview
LK-168A
Бренд: U & Me Brothers Страницы: 6
RAM 2011 DAKOTA User Manual preview
2011 DAKOTA
Бренд: RAM Страницы: 76
Advantech TREK-550 Manual preview
TREK-550
Бренд: Advantech Страницы: 59
Mercedes-Benz AMG E-Class Supplement Manual preview
AMG E-Class
Бренд: Mercedes-Benz Страницы: 54

Бренды по названию

Популярные бренды

Загрузить еще бренды