manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-155

23) Apply A/T fluid to new brake drum gasket (1), then 

install it to transaxle case.

24) Apply A/T fluid to 2nd brake retaining plate (1), discs 

(2) and separator plates (3), then install them to 
transaxle case.

25) Install 2nd brake return spring subassembly (1) to 

transaxle case.

26) Apply A/T fluid to 2nd brake piston assembly (1), and 

align the projection of 2nd brake piston assembly 
with the groove of transaxle case, then put together.

27) Install 2nd brake piston snap ring (1) by using 

special tool and hydraulic press.

CAUTION:

Do not damage 2nd brake piston assembly, 
return spring subassembly, plates and discs 
by pressing in 2nd brake assembly passing 
through its original installing position over 
0.4 mm (0.016 in.).

 

Special tool
(A):  09926–96050

28) After applying A/T fluid to front sun gear thrust 

bearing race (2), install it to front planetary sun gear 
(1).

29) Apply A/T fluid to front planetary sun gear (1) and 

install it to planetary gear assembly (2).

I2RH0B510279-

2

3

1

I2RH0B510280-

1

I2RH0B510281-

I2RH0B510282-

I2RH0B510283-

I2RH0B510285-

I2RH0B510286-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Camcar 40000 Manual preview
40000
Бренд: Camcar Страницы: 6
Daihatsu TERIOS J100 Maintenance Manual preview
TERIOS J100
Бренд: Daihatsu Страницы: 43
Federal Signal Corporation CommCenter D1 Series Installation And Service Instructions Manual preview
CommCenter D1 Series
Бренд: Federal Signal Corporation Страницы: 16
Mazda 2012 Mazda6 Owner'S Manual preview
2012 Mazda6
Бренд: Mazda Страницы: 527
Cadillac 2008 Escalade EXT Owner'S Manual preview
2008 Escalade EXT
Бренд: Cadillac Страницы: 496
Whispbar K783W Fitting Instructions Manual preview
K783W
Бренд: Whispbar Страницы: 16
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Бренд: Mercedes-Benz Страницы: 388
Standby L54 Manual preview
L54
Бренд: Standby Страницы: 10
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Бренд: Haibang Страницы: 6
IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Бренд: IBASE Technology Страницы: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Бренд: Modifry Products Страницы: 2
TATA Motors TIGOR EV 2021 Owner'S Manual preview
TIGOR EV 2021
Бренд: TATA Motors Страницы: 236
Veigel S47290920 Installation And Operating Instructions Manual preview
S47290920
Бренд: Veigel Страницы: 24
Cellular Line interphone Instruction Manual preview
interphone
Бренд: Cellular Line Страницы: 25
HAUL MASTER 41782 Assembly And Operating Instructions Manual preview
41782
Бренд: HAUL MASTER Страницы: 8
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Бренд: RAM Страницы: 174
Chevrolet Malibu 2014 Owner'S Manual preview
Malibu 2014
Бренд: Chevrolet Страницы: 428
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Бренд: STARLANE Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды