manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

2B-18 Front Suspension: 

9) Connect muffler No.1 mounting (1) to suspension 

frame (2).

10) Install steering gear case No.1 bolts (a) and No.2 

bolts (b) to specified torque

Tightening torque
Steering gear case No.1 bolt (a):  55 N·m (5.5 kg-
m, 40.0 lb-ft)
Steering gear case No.2 bolt (b):  55 N·m (5.5 kg-
m, 40.0 lb-ft)

11) Remove supporting device from engine.

12) Install stabilizer joints (1), and tighten nuts to 

specified torque.
When tightening, hold stud with special tools.

Special tool
(A):  09900–00411 (socket)
(B):  09900–00413 (5 mm)

Tightening torque
Stabilizer joint nut (a):  50 N·m (5.0 kg-m, 36.5 lb-
ft)

13) Install suspension control arm referring to 

“Suspension Control Arm / Bushing Removal and 
Installation: ”.

14) Install wheels (right & left) and lower hoist.
15) Confirm front wheel alignment referring to “Front 

Wheel Alignment Inspection and Adjustment: ”.

Front Suspension Frame Check

S4RS0A2206020

Inspect for cracks, deformation or damage.
If defective, replace.

1

2

I4RS0A220040-

I4RS0A220050-

1

1

(A)

(A)

(a)

(a)

(B)

(B)

I4RS0A220051-

I4RS0A220054-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Happy Orange USB-C Quick Start Manual preview
USB-C
Бренд: Happy Orange Страницы: 2
OEM Tools 22505 Operating Instructions And Parts Manual preview
22505
Бренд: OEM Tools Страницы: 4
Uniden BTSC1500 Owner'S Manual preview
BTSC1500
Бренд: Uniden Страницы: 16
Uniden BTSC1500 User Manual preview
BTSC1500
Бренд: Uniden Страницы: 20
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Бренд: Club Car Страницы: 48
VDO VIEWLINE 52 MM - MOUNTING 11-09 Installation Instructions preview
VIEWLINE 52 MM - MOUNTING 11-09
Бренд: VDO Страницы: 4
Actia SmarTach Manual preview
SmarTach
Бренд: Actia Страницы: 102
Pyle PLDCP3 User Manual preview
PLDCP3
Бренд: Pyle Страницы: 2
AMP Research BEDXTENDER HD MAX 74841-00A Assembly Installation Manual preview
BEDXTENDER HD MAX 74841-00A
Бренд: AMP Research Страницы: 9
Belkin F8V7058-APL User Manual preview
F8V7058-APL
Бренд: Belkin Страницы: 2
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Бренд: Lantronix Страницы: 51
Anker Technology Roav VIVA Owner'S Manual preview
Roav VIVA
Бренд: Anker Technology Страницы: 8
Black+Decker BXAE00011 Operating Instructions Manual preview
BXAE00011
Бренд: Black+Decker Страницы: 21
Beeper RW050RF User& Installer'S Manual preview
RW050RF
Бренд: Beeper Страницы: 20
Mercedes-Benz 2007 SLR Mclaren Operator'S Manual preview
2007 SLR Mclaren
Бренд: Mercedes-Benz Страницы: 425
Magneti Marelli Obd Road User Manual preview
Obd Road
Бренд: Magneti Marelli Страницы: 9
Conrad TPMS-001 Operating Instructions Manual preview
TPMS-001
Бренд: Conrad Страницы: 8
Safe Fleet PRIME DESIGN UXV 211 Quick Start Manual preview
PRIME DESIGN UXV 211
Бренд: Safe Fleet Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды