manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine Mechanical:  1D-10

2) Remove oil, old sealant, and dust from sealing 

surfaces on cylinder head and cover. After cleaning, 
apply sealant “A” to the following point.
• Cylinder head cover gasket (1) sealing surface 

area (2) as shown.

“A”:  Water tight sealant 99000–31250

• Timing chain cover (1) and cylinder head (2) 

mating surface as shown.

“A”:  Water tight sealant 99000–31250

3) Install cylinder head cover to cylinder head.

NOTE:
When installing cylinder head cover, use care 
so that cylinder head cover gasket or spark 
plug hole gaskets will not get out of place or 
fall off.

 

4) Tightening bolts in such order as indicated in the 

figure a little at a time till they are tightened to 
specified torque.

Tightening torque
Cylinder head cover bolt (a):  8 N·m (0.8 kg-m, 
6.0 lb-ft)

5) Connect PCV hose (2) to PCV valve (1).
6) Connect breather hose (4).
7) Install oil level gauge.

8) Install wire harness clamp to cylinder head cover.
9) Install ignition coil assemblies with high-tension cord.

10) Connect ignition coil couplers and clamp harness 

securely.

11) Install cylinder head upper cover.

12) Install air cleaner case and resonator.
13) Connect negative cable at battery.

I2RH0B140035-

I2RH0B140036-

I2RH0B140037-

I3RH0B140016-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Horn Tools HISDMSPTRA01 Mounting Instructions preview
HISDMSPTRA01
Бренд: Horn Tools Страницы: 6
Alpine KCE-G7QI Installation preview
KCE-G7QI
Бренд: Alpine Страницы: 2
Whispbar K896W Fitting Instructions Manual preview
K896W
Бренд: Whispbar Страницы: 15
Chevrolet Camaro 12000 1968 Series Factory Assembly Instruction Manual preview
Camaro 12000 1968 Series
Бренд: Chevrolet Страницы: 455
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Бренд: Subaru Страницы: 34
AC Schnitzer DKG Fitting Instructions Manual preview
DKG
Бренд: AC Schnitzer Страницы: 16
Webasto CC4E Installation And Service Instructions Manual preview
CC4E
Бренд: Webasto Страницы: 34
Rati Armster 2 User Manual preview
Armster 2
Бренд: Rati Страницы: 2
LXE Akerstroms Tx700 Configuration Manual preview
Akerstroms Tx700
Бренд: LXE Страницы: 146
MAcarbon MAA.R8.06 Install Instructions preview
MAA.R8.06
Бренд: MAcarbon Страницы: 3
EUFAB 11512 Manual preview
11512
Бренд: EUFAB Страницы: 4
Lund Tonno Pro Installation Instructions Manual preview
Tonno Pro
Бренд: Lund Страницы: 12
Subaru S0A367010 Installation Instructions preview
S0A367010
Бренд: Subaru Страницы: 2
ECS Electronics CT-050-B1 Fitting Instructions Manual preview
CT-050-B1
Бренд: ECS Electronics Страницы: 42
Safe Fleet PRIME DESIGN UXV 211 Quick Start Manual preview
PRIME DESIGN UXV 211
Бренд: Safe Fleet Страницы: 8
3SIXT 3S-1802 Operating Instructions preview
3S-1802
Бренд: 3SIXT Страницы: 4
Toyota 20111 Highlander Brochure preview
20111 Highlander
Бренд: Toyota Страницы: 9
Kuda-Phonebase 291790 Installation Instruction preview
291790
Бренд: Kuda-Phonebase Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды