manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-81

DTC P1878: Torque Converter Clutch Shudder

S4RS0A5104057

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

WARNING:

• When performing a road test, select a place where there is no traffic or possibility of a traffic 

accident and be very careful during testing to avoid occurrence of an accident.

• Road test should be carried out with 2 persons, a driver and tester, on a level road.

 

1) Connect scan tool to DLC with ignition switch OFF.
2) Clear DTCs in TCM and ECM memories by using scan tool.
3) Start engine and warm it up to normal operating temperature.
4) Drive vehicle with 3rd or 4th gear in “D” range and slip controlled lock-up ON for 20 seconds or longer referring to 

“Automatic Gear Shift Table: ”.

5) Stop vehicle.
6) Check DTC, pending DTC and freeze-frame data.

DTC Troubleshooting

DTC detecting condition

Trouble area

The acceleration slip control function stops when the variation in the 
output revolution speed of the specified amplitude and specified cycle 
is detected within a specified period of time. When the specified 
variation is not detected after the acceleration slip control stops.

• Mismatching ATF
• Torque converter clutch malfunction
• Valve body

Step

Action

Yes

No

1

Was “A/T System Check” performed?

Go to Step 2.

Go to “A/T System 
Check: ”.

2

Change A/T fluid referring to “A/T Fluid Change: ”.
Check DTC after performing “DTC Confirmation Procedure”.

Is DTC P1878 still indicated?

Faulty torque converter 
clutch.
Replace torque 
converter.

System is in good 
condition.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Lancia THESIS CONNECT Owner'S Handbook Manual preview
THESIS CONNECT
Бренд: Lancia Страницы: 386
Honda 08A28-0J6-800 Installation Instructions Manual preview
08A28-0J6-800
Бренд: Honda Страницы: 32
AC Schnitzer X3 M-Technik Fitting Instructions Manual preview
X3 M-Technik
Бренд: AC Schnitzer Страницы: 20
Cadillac Escalade ESV 2014 Owner'S Manual preview
Escalade ESV 2014
Бренд: Cadillac Страницы: 508
Hama Liberty III Quick Start Manual preview
Liberty III
Бренд: Hama Страницы: 2
Marlon Xplore Pro II SxS Owner’S Manual Assembly & Installation Instructions preview
Xplore Pro II SxS
Бренд: Marlon Страницы: 15
Waeco 8885100124 Operating Manual preview
8885100124
Бренд: Waeco Страницы: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Бренд: VBG Страницы: 16
BMW M5 2014 Service And Warranty Information preview
M5 2014
Бренд: BMW Страницы: 38
THIEYE CarView 2 User Manual preview
CarView 2
Бренд: THIEYE Страницы: 88
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Бренд: Whelen Engineering Company Страницы: 2
Prime Design URX-001-E Assembly Instructions Manual preview
URX-001-E
Бренд: Prime Design Страницы: 8
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Бренд: IOGear Страницы: 38
Lock'er Down 2011 X Instructions preview
2011 X
Бренд: Lock'er Down Страницы: 2
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Бренд: AUTOTECH Страницы: 4
Ranger design 1525-NSX Quick Start Manual preview
1525-NSX
Бренд: Ranger design Страницы: 22
Rugged Ridge 13551.33 Manual preview
13551.33
Бренд: Rugged Ridge Страницы: 3
Car-Interface CI-RL4-R40 Manual preview
CI-RL4-R40
Бренд: Car-Interface Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды