Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Страница: 558 / 1257

5A-18 Automatic Transmission:
) P0717
Input / Turbine speed sensor
circuit no signal No sensor signal is detected although output
speed sensor signal is inputted.
1 driving cycle
) P0722
Output speed sensor circuit no
signal No sensor signal is inputted although input
speed sensor signal is inputted.
1 driving cycle
) P0741
Torque converter clutch circuit
performance or stuck off
Difference in revolution between engine and
input shaft is too large although TCM is
commanding TCC solenoid to turn ON.
2 driving cycles
) P0742
Torque converter clutch circuit
stuck on
Difference in revolution between engine and
input shaft is too small although TCM is
commanding TCC solenoid to turn OFF.
2 driving cycles
) P0751
Shift solenoid-A (No.1)
performance or stuck off Actual gear position is 3rd gear although TCM
command is for 2nd gear.
2 driving cycles
) P0752 Shift solenoid-A (No.1) stuck on
Actual gear position is 2nd gear although TCM
command is for 3rd gear.
2 driving cycles
) P0756
Shift solenoid-B (No.2)
performance or stuck off Actual gear position is 3rd gear although TCM
command is for 4th gear.
2 driving cycles
) P0757 Shift solenoid-B (No.2) stuck on
Actual gear position is 4th gear although TCM
command is for 3rd gear.
2 driving cycles
) P0787
Shift / Timing solenoid control
circuit low
Voltage of timing solenoid terminal is low
although TCM is commanding timing solenoid to
turn ON.
1 driving cycle
) P0788
Shift / Timing solenoid control
circuit high
Voltage of timing solenoid terminal is high
although TCM is commanding timing solenoid to
turn OFF.
1 driving cycle
) P0962
Pressure control solenoid control
circuit low No electric flow is detected on pressure control
solenoid circuit.
1 driving cycle
) P0963
Pressure control solenoid control
circuit high Too much electric flow is detected on pressure
control solenoid circuit.
1 driving cycle
) P0973
Shift solenoid-A (No.1) control
circuit low Voltage of shift solenoid terminal is low although
TCM is commanding shift solenoid to turn ON.
1 driving cycle
) P0974
Shift solenoid-A (No.1) control
circuit high
Voltage of shift solenoid terminal is high
although TCM is commanding shift solenoid to
turn OFF.
1 driving cycle
) P0976
Shift solenoid-B (No.2) control
circuit low Voltage of shift solenoid terminal is low although
TCM is commanding shift solenoid to turn ON.
1 driving cycle
) P0977
Shift solenoid-B (No.2) control
circuit high
Voltage of shift solenoid terminal is high
although TCM is commanding shift solenoid to
turn OFF.
1 driving cycle
) P1702
Internal control module memory
check sum error
Calculation of current data stored in TCM is not
correct comparing with pre-stored checking data
in TCM.
1 driving cycle
) P1703
CAN invalid data - from other
ECU(s)
TCM receives malfunction signal of throttle
position, engine coolant temperature, engine
revolution and engine torque from ECM.
*1
) P1723 Range select switch malfunction
“3” position switch ON signal is inputed although
transmission range switch signal is inputed P, R,
N or L. range.
*1
) P1774
Control module communication
bus off Transmitting and receiving error detected to
TCM for specified time continuously.
1 driving cycle
) P1775
High speed can communication
bus (Transmission error) Transmitting error detected to TCM for specified
time continuously.
1 driving cycle
) P1777
TCM lost communication with
ECM (Reception error) Receiving error from ECM detected to TCM for
specified time continuously.
1 driving cycle
) P1778
TCM lost communication with
BCM (Reception error) Receiving error from BCM detected to TCM for
specified time continuously.
*1
) P1878 Torque converter clutch shudder
Variation in the output revolution speed of the
specified amplitude and specified cycle is
detected under slip lock-up condition.
*1
DTC No. Detecting item
Detecting condition
(DTC will set when detecting)
Driving cycle
when MIL lighted