manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

4E-11 ABS: 

Scan Tool Data Definition
Battery Volt (V):  

Battery Voltage is an analog input 

signal read by the ABS control module. Certain ABS 
control module functions will be modified if the 
battery voltage falls below or rises above 
programmed thresholds.

Pump Motor Driver (V):  

This parameter indicates the 

operational condition of the pump motor driver 
(transistor).

RF Wheel Speed, LF Wheel Speed, RR Wheel Speed 

and LF Wheel Speed (km/h, MPH):  

Wheel speed 

is an ABS control module internal parameter. It is 
computed by reference pulses from the wheel speed 
sensor.

Brake Switch (ON, OFF):  

This switch signal informs 

the ABS control module whether the brake is active 
or not.

ABS Warning Lamp Does Not Come ON at Ignition Switch ON

S4RS0A4504008

Wiring Diagram

Circuit Description

Operation (ON/OFF) of ABS warning lamp is controlled by ABS control module through lamp driver module in 
combination meter.
If the antilock brake system is in good condition, ABS control module turns ABS warning lamp ON at the ignition switch 
ON, keeps it ON for 2 seconds and then turns it OFF. If an abnormality in the system is detected, ABS warning lamp is 
turned ON continuously by ABS control module. Also, it is turned ON continuously by lamp driver module when the 
connector of ABS control module is disconnected.

Troubleshooting

I4RS0A450010-

[A]: ABS hydraulic unit / control module connector E03

4. Circuit fuse box

8. Lamp driver module

1. Battery

5. Combination meter

9. ABS hydraulic unit / control module assembly

2. Main fuse box

6. ABS warning lamp 

3. Ignition switch

7. EBD warning lamp (Brake warning lamp)

Step

Action

Yes

No

1

1) Turn ignition switch to ON position.

Do other warning lamps come ON?

Go to Step 2.

Go to Step 4.

2

1) Turn OFF ignition switch.
2) Disconnect ABS hydraulic unit / control module 

connector.

3) Turn ON ignition switch.

Does ABS warning lamp light with ignition switch ON?

Replace ABS hydraulic 
unit / control module 
assembly.

Go to Step 3.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Kathrein DDA Series User Manual preview
DDA Series
Бренд: Kathrein Страницы: 7
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Бренд: Porsche Страницы: 144
Audiovox UniStreamONE Installation Manual preview
UniStreamONE
Бренд: Audiovox Страницы: 24
Mercedes-Benz GLE Coupe Brief Overview preview
GLE Coupe
Бренд: Mercedes-Benz Страницы: 2
Westin 25-0560 Instructions preview
25-0560
Бренд: Westin Страницы: 2
Xblitz Mirror 2016 User Manual preview
Mirror 2016
Бренд: Xblitz Страницы: 30
P-Invent Troller User Manual preview
Troller
Бренд: P-Invent Страницы: 4
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Бренд: Ecco Страницы: 12
Qeedon Higlow Series Product Instruction preview
Higlow Series
Бренд: Qeedon Страницы: 2
v.LOGiC V5-CIC-E-PNP Manual preview
V5-CIC-E-PNP
Бренд: v.LOGiC Страницы: 22
Mobileye C2-270 User Manual preview
C2-270
Бренд: Mobileye Страницы: 29
Alfa Romeo Giulietta 2.0 JTDM Manual preview
Giulietta 2.0 JTDM
Бренд: Alfa Romeo Страницы: 14
Axxess AXDSPX-TY1 Installation Instructions Manual preview
AXDSPX-TY1
Бренд: Axxess Страницы: 16
V8 equipment E.BEX Manual preview
E.BEX
Бренд: V8 equipment Страницы: 34
Metra Electronics 99-7804 Installation Instructions Manual preview
99-7804
Бренд: Metra Electronics Страницы: 10
Yakima LockNLoad LightenUp Manual preview
LockNLoad LightenUp
Бренд: Yakima Страницы: 13
FALCON RIDGE KY-700-2018-DRW01 Instructions For Installation And Care preview
KY-700-2018-DRW01
Бренд: FALCON RIDGE Страницы: 7
CITROËN c4 picasso 2006 Owner'S Manual preview
c4 picasso 2006
Бренд: CITROËN Страницы: 266

Бренды по названию

Популярные бренды

Загрузить еще бренды