manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

2B-8 Front Suspension: 

5) Compare strut resistance and number of rebalance 

on the right with those on the left. And they must be 
equal in both. With proper strut, vehicle body should 
come to stop the moments hands are off or after only 
one or two small rebalances.

If conditions of struts are in doubt, compare them with 
known-good vehicle or strut.
• Inspect bearing for wear, abnormal noise or gripping.

If defective, replace.

• Inspect spring seat for cracks or deformation.

If defective, replace.

• Inspect bump stopper for deterioration.

If defective, replace.

• Inspect rebound stopper and strut mount for wear, 

cracks or deformation.
If defective, replace.

Front Wheel Hub and Steering Knuckle Components

S4RS0A2206009

Front Wheel Hub, Steering Knuckle and Wheel 
Bearing Removal and Installation

S4RS0A2206010

Removal

1) Hoist vehicle and remove wheel.
2) Uncaulk drive shaft nut (1).
3) Depress foot brake pedal and hold it there. Remove 

drive shaft nut (1).

4) Remove caliper carrier bolts.

5) Remove caliper (1) with carrier.

NOTE:
Hang removed caliper with a wire hook or the 
like (3) so as to prevent brake hose (4) from 
bending and twisting excessively or being 
pulled.
Don operate brake pedal with pads removed.

 

I4RS0A220015-

1. Front wheel hub

4. Steering knuckle

: 175 N

˜

m (17.5 kg-m, 126.5 lb-ft)

2. Circlip

5. Drive shaft nut

: Calk, after tightening.

: Do not reuse.

3. Wheel bearing

: Face grooved rubber seal side to wheel hub.

6. Hub bolt

I4RS0A220016-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Jabra FREEWAY Datasheet preview
FREEWAY
Бренд: Jabra Страницы: 2
Jabra BT330 User Manual preview
BT330
Бренд: Jabra Страницы: 38
iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Бренд: iDataLink Страницы: 99
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Бренд: PUTCO Страницы: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Бренд: Westfalia Страницы: 18
CALIMA 46008 Operating Instructions Manual preview
46008
Бренд: CALIMA Страницы: 9
Voxoa MCU-20A(P40) User Manual preview
MCU-20A(P40)
Бренд: Voxoa Страницы: 48
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Бренд: SCC Страницы: 4
Reese Explore 63153 Instruction Manual preview
63153
Бренд: Reese Explore Страницы: 9
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Бренд: Cadillac Страницы: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Бренд: TIE DOWN Страницы: 2
DEFA MultiCharger 1204 User'S Installation Manual preview
MultiCharger 1204
Бренд: DEFA Страницы: 28
Steelmate PTS800V7 User Manual preview
PTS800V7
Бренд: Steelmate Страницы: 14
J. Strong JST506BT Installation Instructions preview
JST506BT
Бренд: J. Strong Страницы: 2
HAKR TRIP 3 Instructions For Use Manual preview
TRIP 3
Бренд: HAKR Страницы: 9
Rigid Hitch BULL BAR Installation Instructions preview
BULL BAR
Бренд: Rigid Hitch Страницы: 2
Westin 32-1660 Instructions preview
32-1660
Бренд: Westin Страницы: 3
Brodit Getac T800 Quick Start Manual preview
Getac T800
Бренд: Brodit Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды