manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Rear Suspension:  2C-3

Repair Instructions

Rear Shock Absorber Removal and Installation

S4RS0A2306028

Removal

1) Hoist vehicle.
2) Remove tail end member trim (1) and quarter inner 

trim (2).

3) Support rear axle by using floor jack to prevent it 

from lowering.

4) Remove absorber lower nut.
5) Remove absorber upper nut. Then remove shock 

absorber.

Installation

1) Install shock absorber (1).

Tighten new rear shock absorber upper nut and 
lower nut temporarily at this step.

CAUTION:

Never reuse the removed rear shock 
absorber upper nut.

 

2) Remove floor jack (2) from rear axle and lower hoist.
3) Tighten nuts to specified torque.

Tightening torque
Rear shock absorber upper nut (a):  25 N·m (2.5 
kg-m, 18.0 lb-ft)
Rear shock absorber lower nut (b):  90 N·m (9.0 
kg-m, 65.0 lb-ft)

4) Install tail end member trim (1) and quarter inner trim 

(2).

3. Clip

3

3

2

3

1

3

I4RS0A230003-

3. Clip

(a)

1

(b)

2

I4RS0A230004-

3

3

2

3

1

3

I4RS0A230003-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Daihatsu G200 Service Manual preview
G200
Бренд: Daihatsu Страницы: 485
Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Бренд: Gardigo Страницы: 36
Zavoli Bora Technical Instructions And Installation Manual preview
Bora
Бренд: Zavoli Страницы: 26
Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Бренд: Quadratec Страницы: 20
Camcar 40061 Fe Mounting Instructions preview
40061 Fe
Бренд: Camcar Страницы: 2
Audiovox Prestige APS-45B Installation Manual preview
Prestige APS-45B
Бренд: Audiovox Страницы: 8
Volvo 1985 740 GL Owner'S Manual preview
1985 740 GL
Бренд: Volvo Страницы: 138
FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Бренд: FORM FIT Страницы: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Бренд: Thule Страницы: 12
FORM FIT 1303 Installation Instructions preview
1303
Бренд: FORM FIT Страницы: 2
kincrome K12071 Owner'S Assemble And Operating Manual preview
K12071
Бренд: kincrome Страницы: 6
Alfa Romeo Alfa 147 Quick Start Manual preview
Alfa 147
Бренд: Alfa Romeo Страницы: 8
Kuda 079020 Installation Instruction preview
079020
Бренд: Kuda Страницы: 2
Gator GRM430EM User Manual preview
GRM430EM
Бренд: Gator Страницы: 6
BMW FXX ATM Emulator User And Installation Manual preview
FXX ATM Emulator
Бренд: BMW Страницы: 5
Vauxhall Crossland X 2017 Owner'S Manual preview
Crossland X 2017
Бренд: Vauxhall Страницы: 245
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Бренд: Cadillac Страницы: 19
Kuda 076100 Installation Instruction preview
076100
Бренд: Kuda Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды