manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

8B-22 Air Bag System: 

NOTE:
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components and ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance: ”, if any.
• Repeat “Air Bag Diagnostic System Check: ” to confirm that the trouble has been corrected.

 

2

1) With ignition switch OFF, disconnect SDM connector.
2) Check proper connection to SDM at “L29-26” terminal.
3) If OK, turn ignition switch ON and then check voltage 

between “L29-26” terminal on SDM connector and body 
ground.

Special tool
(A):  09932-76010

Is voltage 8 V or more?

Go to Step 4.

Go to step 3.

3

1) With ignition switch OFF, disconnect on connector “L04” 

junction block assembly.

2) Check proper connection at “L04-1” terminal.
3) If OK, turn ignition switch ON and then check voltage 

between “L04-1” terminal and body ground.

Is voltage 8 V or more?

Go to Step 4.

Check circuit from 
battery to “L04” 
connector and charging 
system.

4

1) With ignition switch OFF, reconnect SDM connector.

With ignition switch ON, does DTC B1017 exist?

Substitute a known-
good SDM and recheck.

Check charging system 
and repair as necessary 
referring to “Generator 
Test (Undercharged 
Battery Check):  in 
Section 1J”.

Step

Action

Yes

No

(A)

"L29-26"

I4RS0A820100-

"L04-1"

I4RS0A820012-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

FANATEC Porsche 911 Turbo S Wheel Developer Quick Manual preview
Porsche 911 Turbo S Wheel
Бренд: FANATEC Страницы: 9
Toyota RX450h 2010 Emergency Response Manual preview
RX450h 2010
Бренд: Toyota Страницы: 35
Webasto Transit Vancouver Wagon Manual preview
Transit Vancouver Wagon
Бренд: Webasto Страницы: 44
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Бренд: AutoWatch Страницы: 4
AddSecure Asset Light Installation Manual preview
Asset Light
Бренд: AddSecure Страницы: 14
Nav TV PCM3CAM Install Manual preview
PCM3CAM
Бренд: Nav TV Страницы: 4
E&G Classics 1409-0102-10 Installation Instructions preview
1409-0102-10
Бренд: E&G Classics Страницы: 3
Sanitas SMG 245 Instructions For Use Manual preview
SMG 245
Бренд: Sanitas Страницы: 36
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
Ford Mustang 2007 Supplement Manual preview
Mustang 2007
Бренд: Ford Страницы: 40
Oldsmobile Bravada 1997 Owner'S Manual preview
Bravada 1997
Бренд: Oldsmobile Страницы: 358
Rugged Ridge 53701.52 Installation Manual preview
53701.52
Бренд: Rugged Ridge Страницы: 5
Kleinn RS-GM6 Installation Manual preview
RS-GM6
Бренд: Kleinn Страницы: 8
MayPole BC2085 Manual preview
BC2085
Бренд: MayPole Страницы: 3
Charge Amps Halo Pole Mount Manual preview
Halo Pole Mount
Бренд: Charge Amps Страницы: 14
Westfalia 17 56 46 Instruction Manual preview
17 56 46
Бренд: Westfalia Страницы: 2
Nav TV MOST-HUR31 Manual preview
MOST-HUR31
Бренд: Nav TV Страницы: 8
Haltech NEXUS R3 Quick Start Manual preview
NEXUS R3
Бренд: Haltech Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды