manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-96 Automatic Transmission: 

Transmission Range Sensor (Shift Switch) 
Inspection and Adjustment

S4RS0A5106008

1) Shift manual select lever (4) to “N” range.
2) Check that needle direction shaped on lock washer 

(2) and “N” reference line (1) on transmission range 
sensor are aligned. If not, loosen sensor bolts (3) 
and align them.

Tightening torque
Transmission range sensor bolt (a):  5.5 N·m (
0.55 kg-m, 4.0 lb-ft)

3) Check that engine starts in “N” and “P” ranges but it 

doesn’t start in “D”, “2”, “L” or “R” range. Also, check 
that back-up lamp lights in “R” range.
If faulty condition cannot be corrected by adjustment, 
disconnect transmission range sensor connector 
and check that continuity exists as shown by moving 
manual select lever.

Output Shaft Speed Sensor (VSS) Removal and 
Installation

S4RS0A5106009

Removal

1) Disconnect negative cable at battery.
2) Disconnect output shaft speed sensor connector (2).
3) Remove output shaft speed sensor (VSS) (1) by 

removing its bolt.

Installation

1) Apply A/T fluid to output shaft speed sensor O-ring.
2) Install output shaft speed sensor (VSS) (1) to A/T 

case and tighten bolt to specified torque.

Tightening torque
Output shaft speed sensor (VSS) bolt (a):  13 
N·m (1.3 kg-m, 9.5 lb-ft)

3) Connect output shaft speed sensor connector (2) to 

output shaft speed sensor (VSS) (1).

4) Connect negative cable to battery.

I3RM0B510038-

4

3

2

1

9

8

7

6

5

1

2

3

4

5

6

7

8

9

P

R

N

D

2

L

I3RM0B510039-

I3RM0B510040-

I3RM0B510041-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Back View RV-250 User Manual preview
RV-250
Бренд: Back View Страницы: 168
Brodit ProClip 804438 Installation Instructions preview
ProClip 804438
Бренд: Brodit Страницы: 2
REVCAMUK MON16AHD Instructions preview
MON16AHD
Бренд: REVCAMUK Страницы: 4
POOL-LINE 110085 Assembly Instructions preview
110085
Бренд: POOL-LINE Страницы: 2
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Бренд: Vauxhall Страницы: 95
Mobileye C2-270 User Manual preview
C2-270
Бренд: Mobileye Страницы: 29
TomTom LINK 105 Installation Manual preview
LINK 105
Бренд: TomTom Страницы: 22
Sintrones SBOX-2320 User Manual preview
SBOX-2320
Бренд: Sintrones Страницы: 55
Butts of Bawtry TBT4700 Quick Start Manual preview
TBT4700
Бренд: Butts of Bawtry Страницы: 2
Belkin LineCast Auto FM User Manual preview
LineCast Auto FM
Бренд: Belkin Страницы: 15
Rover 75 Saloon Owner'S Handbook Manual preview
75 Saloon
Бренд: Rover Страницы: 285
Xpresskit 20110601 Installation Manual preview
20110601
Бренд: Xpresskit Страницы: 12
Rhino-Rack S400-FK2 Instructions preview
S400-FK2
Бренд: Rhino-Rack Страницы: 2
Nav TV NTV-KIT850 Install Manual preview
NTV-KIT850
Бренд: Nav TV Страницы: 11
Subaru 1999 Legacy Owner'S Manual preview
1999 Legacy
Бренд: Subaru Страницы: 399
Mid America Motorworks 602-781 Instruction Sheet preview
602-781
Бренд: Mid America Motorworks Страницы: 2
Chrysler DODGE AD100 1993 Service Manual preview
DODGE AD100 1993
Бренд: Chrysler Страницы: 1502
Westfalia 300025300113 Installation Instructions Manual preview
300025300113
Бренд: Westfalia Страницы: 97

Бренды по названию

Популярные бренды

Загрузить еще бренды