manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Suspension General Diagnosis:  2A-2

NOTE:
*1: Right-to-left trim height (“H”) difference should be within 15 mm (0.6 in.) with curb weight. (same 
with rear side.)

 

Body leans or sways in 
corners

Loose stabilizer bar

Tighten stabilizer bar bolts or nuts, or replace 
bushes.

Faulty struts (shock absorbers) or 
mountings

Replace strut or tighten mounting.

Broken or sagging springs

Replace.

Overloaded

Check loading.

Cupped tires

Front struts defective

Replace.

Worn wheel bearings

Replace.

Excessive tire or wheel run-out

Replace tire or wheel disc.

Worn ball joints

Replace front suspension arm.

Tire out of balance

Adjust tire balance.

Condition

Possible cause

Correction / Reference Item

“H”

I2RH01210001-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

TATA Motors Nano Owner'S Manual & Service Book preview
Nano
Бренд: TATA Motors Страницы: 94
GÄN GA Manual preview
GA
Бренд: GÄN Страницы: 24
TUFLOC Dodge Charger TufBox Installation Instructions Manual preview
Dodge Charger TufBox
Бренд: TUFLOC Страницы: 6
Thule 1511 Instructions Manual preview
1511
Бренд: Thule Страницы: 8
RBP STEALTH POWER RBP-216-SP Installation Manual preview
STEALTH POWER RBP-216-SP
Бренд: RBP Страницы: 16
HURST STREET SUPER SHIFTER Installation Instructions preview
STREET SUPER SHIFTER
Бренд: HURST Страницы: 2
RAM Ram Dodge 2010 Owner'S Manual preview
Ram Dodge 2010
Бренд: RAM Страницы: 616
Nav TV AUDI-P60H Install Manual preview
AUDI-P60H
Бренд: Nav TV Страницы: 9
Honda Clarity 2018 Owner'S Manual preview
Clarity 2018
Бренд: Honda Страницы: 81
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Бренд: STARLANE Страницы: 24
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Бренд: H&S Страницы: 32
Yakima RimROC Instructions Manual preview
RimROC
Бренд: Yakima Страницы: 12
Axxess AXDSPX-VW1 Installation Instructions Manual preview
AXDSPX-VW1
Бренд: Axxess Страницы: 16
Audiovox AA-BAT Programming Manual preview
AA-BAT
Бренд: Audiovox Страницы: 3
Victory 4x4 VRKCAP Install Instructions Manual preview
VRKCAP
Бренд: Victory 4x4 Страницы: 9
THIEYE CarView 2 User Manual preview
CarView 2
Бренд: THIEYE Страницы: 88
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Бренд: Saturn Страницы: 440
Gator GT700SD User Manual preview
GT700SD
Бренд: Gator Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды