manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1A-190 Engine General Information and Diagnosis: 

6

A/C evaporator outlet air temp. sensor check

1) Disconnect connectors from ECM with ignition switch 

turned OFF.

2) Check for proper connection to “E23-57” and “E23-54” 

wire terminals of ECM connector.

3) If OK, measure resistance between “E23-57” and “E23-

54” wire terminals of ECM connector.

Evaporator temp. sensor resistance
At 0 

q

C: 6.3 – 6.9 k

:

At 25 

q

C: 1.8 – 2.2 k

:

Is resistance within specification?

Go to Step 7.

Faulty A/C evaporator 
outlet air temp. sensor 
or its circuit.

7

DTC check of A/C refrigerant pressure sensor circuit

1) Connect scan tool to DLC with ignition switch turned 

OFF.

2) Turn ON ignition switch.
3) Check ECM for DTC of A/C refrigerant pressure sensor 

circuit.

Is there DTC P0532 or DTC P0533?

Go to applicable DTC 
diag. flow.

Go to Step 8.

8

A/C refrigerant pressure sensor voltage check

1) Check A/C refrigerant pressure sensor voltage referring 

to “Inspection of ECM and Its Circuits: ”.

Is voltage within specified value?

Go to Step 9.

Check amount of 
refrigerant. If OK, 
replace A/C refrigerant 
pressure sensor.

9

Radiator cooling fan check

1) Check radiator cooling fan referring to “Radiator Cooling 

Fan Motor On-Vehicle Inspection:  in Section 1F”.

Is check result satisfactory?

Radiator cooling fan 
drive circuit malfunction. 
If circuit is OK, go to 
Step 6.

Replace radiator cooling 
fan motor.

10

A/C compressor control system check

Is A/C compressor started when A/C and blower speed 
selector switch are turned ON with engine running?

A/C system is in good 
condition.

Go to Step 11.

Step

Action

Yes

No

7

6

5

4

3

2

1

10

20

30

40

50

0

10

20

30

60

70

80

Resistance

Temperature

I3RB0A110053-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

JETBAG 320 Fitting Instructions Manual preview
320
Бренд: JETBAG Страницы: 44
Wagan 2591 User Manual preview
2591
Бренд: Wagan Страницы: 12
Yakima K618 Instructions Manual preview
K618
Бренд: Yakima Страницы: 11
Jeep 2011 grand cherokee Accessories Quick Reference Manual preview
2011 grand cherokee
Бренд: Jeep Страницы: 22
Jeep 2013 Grand Cherokee Owner'S Manual preview
2013 Grand Cherokee
Бренд: Jeep Страницы: 704
Jeep 2012 Liberty Owner'S Manual preview
2012 Liberty
Бренд: Jeep Страницы: 558
Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Бренд: Yamaha Страницы: 3
Prorack K383 Fitting Instructions Manual preview
K383
Бренд: Prorack Страницы: 14
Connects2 adaptiv mini ADVM-BM1 Fitting & User Manual preview
adaptiv mini ADVM-BM1
Бренд: Connects2 Страницы: 4
StowAway 2 025.41 Assembly Instructions preview
025.41
Бренд: StowAway 2 Страницы: 2
Skoda KAROQ 2017 Owner'S Manual preview
KAROQ 2017
Бренд: Skoda Страницы: 324
GROM Audio VLINE Installation Manual preview
VLINE
Бренд: GROM Audio Страницы: 20
Honda CRV 2015 Navigation Manual preview
CRV 2015
Бренд: Honda Страницы: 253
Toyota 2018 yaris Vehicle Instruction Card preview
2018 yaris
Бренд: Toyota Страницы: 11
Butts of Bawtry TBT4700 Quick Start Manual preview
TBT4700
Бренд: Butts of Bawtry Страницы: 2
Belkin LineCast Auto FM User Manual preview
LineCast Auto FM
Бренд: Belkin Страницы: 15
Rover 75 Saloon Owner'S Handbook Manual preview
75 Saloon
Бренд: Rover Страницы: 285
Xpresskit 20110601 Installation Manual preview
20110601
Бренд: Xpresskit Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды