manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-83

2

Check TCC solenoid valve circuit for IG short

1) Connect valve body harness connector.
2) Disconnect TCM connectors.
3) Check for proper connection to TCM at terminal “C34-3” 

and “C34-5”.

4) If connection is OK, turn ignition switch ON and measure 

voltage between terminal “C34-3” of disconnected 
harness side TCM connector and ground between 
terminal “C34-5” of disconnected harness side TCM 
connector and ground.

Are voltage 1 V or less?

Go to Step 3.

“WHT/BLU” or “WHT/
BLK” circuit shorted to 
power circuit.

3

Check TCC lock-up pressure control solenoid valve 
resistance

1) Turn ignition switch OFF.
2) Disconnect valve body harness connector (1), (2) on 

automatic transaxle.

3) Check for proper connection to solenoid at “WHT/BLU” 

and “WHT/BLK” circuits.

4) Check resistance of TCC lock-up pressure control 

solenoid valve.

TCC lock-up pressure control solenoid valve 
resistance
Between terminals of transaxle side valve body 
harness connector: 5.0 – 5.6 

:

 at 20 

q

C (68 

q

F)

Between terminals of transaxle side valve body 
harness connector and transaxle: Infinity

Is check results satisfactory?

Intermittent trouble or 
faulty TCM.
Check for intermittent 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00”.
If OK, substitute a 
known-good TCM and 
recheck.

Replace TCC lock-up 
pressure control 
solenoid valve or lead 
wire.

Step

Action

Yes

No

1

6

7

8

9

10

5

4

3

2

1

2

I4RS0A510020-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Jeep UNIVERSAL CJ-2A Operation Data preview
UNIVERSAL CJ-2A
Бренд: Jeep Страницы: 27
Jeep RENEGADE 2016 User Manual preview
RENEGADE 2016
Бренд: Jeep Страницы: 228
Jeep PATRIOT 2013 User Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 108
Jeep PATRIOT 2013 Owner'S Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 525
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Бренд: SuperATV Страницы: 3
VDO VIEWLINE 52 MM - MOUNTING 11-09 Installation Instructions preview
VIEWLINE 52 MM - MOUNTING 11-09
Бренд: VDO Страницы: 4
Hama 00 123530 Operating Instructions preview
00 123530
Бренд: Hama Страницы: 4
Volvo 1992 850 Service And Repair Manual preview
1992 850
Бренд: Volvo Страницы: 230
GARO Wallbox GLB Quick Start Manual preview
Wallbox GLB
Бренд: GARO Страницы: 15
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Бренд: Acura Страницы: 6
Caraudio-Systems RL-LR12-TF Manual preview
RL-LR12-TF
Бренд: Caraudio-Systems Страницы: 9
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Бренд: Mazda Страницы: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Бренд: Toyota Страницы: 50
WABCO TP19039 Manual preview
TP19039
Бренд: WABCO Страницы: 34
Metra Electronics 99-5026 Installation Instructions Manual preview
99-5026
Бренд: Metra Electronics Страницы: 20
Mazda 3 Facelift 2006 Training Manual preview
3 Facelift 2006
Бренд: Mazda Страницы: 94
Toyota Avalon 2001 Operating Manual preview
Avalon 2001
Бренд: Toyota Страницы: 295
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Бренд: Lexus Страницы: 830

Бренды по названию

Популярные бренды

Загрузить еще бренды