manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1C-10 Engine Electrical Devices: 

Mass Air Flow (MAF) and Intake Air 
Temperature (IAT) Sensor Removal and 
Installation

S4RS0A1306021

CAUTION:

• Do not disassemble MAF and IAT sensor.
• Do not expose MAF and IAT sensor to any 

shock.

• Do not clean MAF and IAT sensor.
• If MAF and IAT sensor has been dropped, it 

should be replaced.

• Do not blow compressed air by using air 

gun or the like.

• Do not put finger or any other object into 

MAF and IAT sensor. Malfunction may 
occur.

 

Removal

1) Disconnect negative cable at battery.
2) Disconnect MAF and IAT sensor connector.
3) Remove air cleaner case (1).
4) Remove MAF and IAT sensor (2) from air cleaner 

case.

Installation

Reverse removal procedure noting the followings.
• Tighten MAF and IAT sensor screws to specified 

torque.

Tightening torque
MAF and IAT sensor screw (a):  1.5 N·m (0.15 kg-
m, 1.1 lb-ft)

• Connect MAF and IAT sensor connector securely.

Mass Air Flow (MAF) and Intake Air 
Temperature (IAT) Sensor Inspection

S4RS0A1306022

CAUTION:

Do not heat up MAF and IAT sensor more 
than 100 

q

C (212 

q

F). Otherwise, MAF and IAT 

sensor will be damaged.

 

• Check sensor O-ring (1) for damage and 

deterioration. Replace as necessary.

• Blow hot air to temperature sensing part (2) of MAF 

and IAT sensor (3) using hot air drier (4) and measure 
resistance between sensor terminals while heating air 
gradually.
If measured resistance does not show such 
characteristic as shown, replace MAF and IAT sensor.

Intake air temperature sensor resistance
–20 

q

C (–4 

q

F): 13.6 – 18.4 k

:

20 

q

C (68 

q

F): 2.21 – 2.69 k

:

60 

q

C (140 

q

F): 0.493 – 0.667 k

:

1

2

I4RS0A130010-

(a)

I4RS0A130011-

[A]: Lower limit
[B]: Nominal

[C]: Upper limit
[D]: Resistance

[E]: Temperature

5. Temperature gauge

20

0

68

32

104

140

176

40

60

80

(2.45)

(0.58)

1

2

3

4

5

[A]

[B]

[E]

[C]

[D]

I4RS0A130012-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

A-Tach Mounts 50131 Instructions preview
50131
Бренд: A-Tach Mounts Страницы: 2
IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Бренд: IAME Страницы: 17
Q'STRAINT QLK-150 Installation Instructions Manual preview
QLK-150
Бренд: Q'STRAINT Страницы: 10
Honda 2004 S2000 Owner'S Manual preview
2004 S2000
Бренд: Honda Страницы: 208
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
Webasto Telestart T91 Installation Instructions Manual preview
Telestart T91
Бренд: Webasto Страницы: 18
Safe Fleet PRIME DESIGN URX-001-E Manual preview
PRIME DESIGN URX-001-E
Бренд: Safe Fleet Страницы: 8
Buick 2015 LaCrosse Getting To Know Manual preview
2015 LaCrosse
Бренд: Buick Страницы: 20
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Бренд: Omix-Ada Страницы: 6
Volvo S90 2018 Quick Manual preview
S90 2018
Бренд: Volvo Страницы: 42
Cadillac GMC Yukon Denali 2005 Owner'S Manual preview
GMC Yukon Denali 2005
Бренд: Cadillac Страницы: 456
Saab 900 5 Speed Technical Training Manual preview
900 5 Speed
Бренд: Saab Страницы: 63
R&G LP0291BK Fitting Instructions Manual preview
LP0291BK
Бренд: R&G Страницы: 20
Whispbar S17W Fitting Instructions Manual preview
S17W
Бренд: Whispbar Страницы: 70
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Бренд: Thule Страницы: 12
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Бренд: Oldsmobile Страницы: 380
ULTIMATE SPEED 285690 Assembly And Safety Advice preview
285690
Бренд: ULTIMATE SPEED Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды