Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 799

Страница: 799 / 1257

Power Assisted Steering System: 6C-26

Voltage Check

1) Remove console box.
2) Check for voltage at each terminal with connectors connected to the P/S control module.

NOTE:
As each terminal voltage is affected by the battery voltage, confirm if the battery voltage is 11 V or
more when ignition switch is ON.

[B]

[C]

[A]

12 13 14 15 16 17 18 19 20

I4RS0A630024-

[A]: Connector “E52” (viewed from harness side)
[B]: Connector “E51” (viewed from harness side)

[C]: Connector “E49” (viewed from harness side)

Terminal

Wire color

Circuit

Normal voltage

Condition

E49-1

GRN

P/S control module power
supply from battery

10 – 14 V

—

E49-2

BLK

Ground

—

E51-1

BLK

Motor output 1

5 – 7 V

Engine idling and steering wheel at
straight position

E51-2

RED

Motor output 2

5 – 7 V

Engine idling and steering wheel at
straight position

E52-1

LT GRN/BLK

P/S control module power
supply from ignition switch

10 – 14 V

Ignition switch ON

E52-2

—

E52-3

—

E52-4

PPL

VSS

*Indicator deflection

repeated 0 – 1 V

and 10 – 14 V

• Ignition switch ON
• Front left tire turned quickly with right

tire locked

E52-5

GRY

“EPS” Light

0 V

“EPS” warning lamp ON

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды