manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

4A-9 Brake Control System and Diagnosis: 

• Perform brake test and check installed part for fluid 

leakage.

Rear Brake Hose / Pipe Removal and 
Installation

S4RS0A4106008

Removal

1) Raise and support vehicle properly. Remove tire and 

wheel.

2) Clean dirt and foreign material from both flexible 

hose end and pipe end fittings.

3) Remove brake flexible hose or pipe.

Installation

Reverse brake flexible hose installation procedure, 
noting the following.
• Fill and maintain brake fluid level in reservoir.
• Bleed brake system. Refer to “Air Bleeding of Brake 

System: ”.

• Perform brake test and check each installed part for 

fluid leakage.

• Never reuse protector nut once removed. Be sure to 

use a new one.

• Install clamps properly referring to the figure and 

tighten bolts.

• When installing hose, make sure that it has no twist or 

kink.

Brake Hose and Pipe Inspection

S4RS0A4106009

Hose

The brake hose assembly should be checked for road 
hazard damage, for cracks and chafing of outer cover, 
for leaks and blisters. A light and mirror may be needed 
for an adequate inspection. If any conditions are 
observed on brake hose, it is necessary to replace it.

Pipe

Inspect the pipe for damage, cracks, dents and 
corrosion. If any defect is found, replace it.

Master Cylinder Components

S4RS0A4106010

I2RH01410012-

I4RS0A410025-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Federal Signal Corporation 7000 Assembly Instructions Manual preview
7000
Бренд: Federal Signal Corporation Страницы: 13
GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Бренд: GMC Страницы: 140
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Бренд: Porsche Страницы: 144
Subaru SPLASH GUARD Installation Manual preview
SPLASH GUARD
Бренд: Subaru Страницы: 3
Dometic GROUP DRS2 Installation And Operating Manual preview
DRS2
Бренд: Dometic GROUP Страницы: 20
Blue Ox BX3781 Installation Instructions Manual preview
BX3781
Бренд: Blue Ox Страницы: 7
Shad NADSA ATV80 Owner'S Manual preview
NADSA ATV80
Бренд: Shad Страницы: 3
Ironton 44596 Owner'S Manual preview
44596
Бренд: Ironton Страницы: 7
Volvo 2004 V70 (Swedish) Användarmanual preview
2004 V70
Бренд: Volvo Страницы: 188
Pyle PLCMRV8B Black User Manual preview
PLCMRV8B Black
Бренд: Pyle Страницы: 4
FALCON RIDGE HO-P500-FC04 Instructions For Installation And Care preview
HO-P500-FC04
Бренд: FALCON RIDGE Страницы: 8
Scosche 142HUD2 Manual preview
142HUD2
Бренд: Scosche Страницы: 8
Mercedes-Benz 2015 SLK Operator'S Manual preview
2015 SLK
Бренд: Mercedes-Benz Страницы: 358
Toyota Sienna 2021 Manual preview
Sienna 2021
Бренд: Toyota Страницы: 600
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Бренд: H&S Страницы: 32
Daesung HM-TX-315 User Manual preview
HM-TX-315
Бренд: Daesung Страницы: 9
Pontiac 2010 Vibe Owner'S Manual preview
2010 Vibe
Бренд: Pontiac Страницы: 318
Ford Mustang 2007 Supplement Manual preview
Mustang 2007
Бренд: Ford Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды