Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 1257

background image

Engine General Information and Diagnosis: 1A-43

DTC Troubleshooting

NOTE:

• Before performed trouble shooting, be sure to read the “Precautions of ECM Circuit Inspection: ”.
• When measuring circuit voltage, resistance and/or pulse signal at ECM connector, connect the

special tool to ECM and/or the ECM connectors referring to “Inspection of ECM and Its Circuits: ”.

• Upon completion of inspection and repair work, perform “DTC Confirmation Procedure” and

confirm that the trouble has been corrected.

Step

Action

Yes

No

1

Was “Engine and Emission Control System Check”
performed?

Go to Step 2.

Go to “Engine and
Emission Control
System Check: ”.

2

Oil control valve electrical circuit check

1) Disconnect connectors from ECM with ignition switch

turned OFF.

2) Check for proper connection at “C37-60” and “C37-59”

terminals of ECM connector.

3) If OK, measure resistance between “C37-60” and “C37-

59” terminals of ECM connector.

Is resistance below 10

:

?

Go to Step 3.

Go to Step 8.

3

Oil control valve electrical circuit check

Was resistance more than 6.5

:

in Step 2?

Go to Step 4.

Go to Step 7.

4

Oil control valve electrical circuit for power short check

1) Turn ON ignition switch.
2) Measure voltage between “C37-60” terminal of ECM

connector and engine ground.

Is voltage below 1 V?

Go to Step 5.

“RED”, “YEL/RED”,
“YEL” or “YEL/GRN”
wire is shorted to power
supply circuit.

5

Oil control valve electrical circuit for ground short
check

1) Disconnect connector from oil control valve with ignition

switch turned OFF.

2) Measure resistance between “C37-60” terminal of ECM

connector and engine ground.

Is resistance infinity?

Go to Step 6.

“YEL/RED” wire is
shorted to ground
circuit.

6

Oil control valve electrical circuit for ground short
check

1) Measure resistance between “C37-59” terminal of ECM

connector and engine ground.

Is resistance infinity?

Go to Step 9.

“YEL/GRN” wire is
shorted to ground
circuit.

7

Oil control valve electrical circuit for short check

1) Disconnect connector from oil control valve with ignition

switch turned OFF.

2) Measure resistance between “C37-60” and “C37-59”

terminals of ECM connector.

Is resistance infinity?

Go to Step 9.

“YEL/RED” wire is
shorted to “YEL/GRN”
wire.

«
...
89
90
91
92
93
...
»

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Бренд: Lancia Страницы: 191

RadioPRO 5 RP5-GM41

Бренд: PAC Страницы: 3

Бренд: Vaisala Страницы: 24

Бренд: Car-Interface Страницы: 23

Бренд: RuggON Страницы: 2

Бренд: Kia Страницы: 10

Бренд: Axxess Страницы: 8

Бренд: Edelbrock Страницы: 2

Бренд: Subaru Страницы: 21

Бренд: Sears Страницы: 41

Бренд: EUFAB Страницы: 12

TRI-FOLD PG9300RF

Бренд: Pet Gear Страницы: 4

Бренд: Toyota Страницы: 600

Бренд: Improved Racing Страницы: 17

1995 Cutlass Supreme

Бренд: Oldsmobile Страницы: 340

Бренд: AutoLoc Страницы: 6

Бренд: rough country Страницы: 4

Бренд: Volvo Страницы: 197

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды