manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

6B-7 Steering Wheel and Column: 

Steering Column Inspection

S4RS0A6206006

Check steering column for damage and operation 
referring to “Checking Steering Column for Accident 
Damage: ”.

Steering Lower Shaft Removal and Installation

S4RS0A6206008

CAUTION:

Never turn steering wheel while steering 
lower shaft is removed.
Should it have been turned and contact coil 
have got out of its centered position, it needs 
to be centered again. Also, turning steering 
wheel more than about two and a half turns 
will break contact coil.

 

Removal

1) Turn steering wheel so that vehicle’s front tires are at 

straight-ahead position.

2) Turn ignition switch to LOCK position and remove 

key.

3) Remove steering joint cover.
4) Make alignment marks (4) on lower shaft (1) and 

shaft joint of steering column (2) and lower shaft (1) 
and pinion shaft (3) for a guide during reinstallation.

5) Remove lower shaft joint bolts (5).
6) Remove steering lower shaft (1).

Installation

1) Be sure that front wheels are in straight forward 

state.

2) Align flat part “A” of steering lower shaft (1) with bolt 

hole “B” of shaft joint (2) of column as shown. Then 
insert lower shaft into shaft joint of steering column 
with matching marks (4).

3) Insert lower shaft (1) into pinion shaft (3) with 

matching marks (4).

4) Tighten joint bolt (pinion shaft side) (6) to specified 

torque first and then joint bolt (steering column side) 
(5) to specified torque.

Tightening torque
Steering shaft joint bolt (a):  25 N·m (2.5 kg-m, 
18.5 lb-ft)

I4RS0A620020-

I4RS0A620021-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Daihatsu Mira Manual preview
Mira
Бренд: Daihatsu Страницы: 340
Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Бренд: Cadillac Страницы: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Бренд: Cadillac Страницы: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Бренд: Cadillac Страницы: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Бренд: Cadillac Страницы: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Бренд: Cadillac Страницы: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Бренд: Cadillac Страницы: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Бренд: Cadillac Страницы: 438
Falcon 1990 Installation Instructions And Specifications preview
1990
Бренд: Falcon Страницы: 8
Laser 4832 Manual preview
4832
Бренд: Laser Страницы: 8
Roav R5141 Owner'S Manual preview
R5141
Бренд: Roav Страницы: 10
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Бренд: muth Страницы: 9
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Бренд: Monacor Страницы: 2
Kuda 182220 Installation Instruction preview
182220
Бренд: Kuda Страницы: 3
Honda 2010 Civic Sedan Owner'S Manual preview
2010 Civic Sedan
Бренд: Honda Страницы: 390
Mini COOPER Owner'S Manual preview
COOPER
Бренд: Mini Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды