manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

4B-5 Front Brakes: 

3) Remove piston seal using a thin blade like a 

thickness gauge, etc.

CAUTION:

Be careful not to damage inside (bore side) of 
cylinder.

 

4) Remove bleeder plug and cap from caliper.

Assembly

Assemble parts in reverse order of disassembly, 
observing the following instructions.

CAUTION:

• Wash each part cleanly before installation 

in the same fluid as the one used in master 
cylinder reservoir.

• Never use other fluid or thinner.
• Before installing piston seal or cylinder 

boot to cylinder, apply brake fluid to them.

• Install a new piston seal into groove in 

cylinder securely making sure that it is not 
twisted.

• Before installing caliper to carrier, install 

slide pin with grease applied into caliper 
carrier hole and check for its smooth 
movement in thrust direction.

• After reassembling brake lines, bleed air 

from them.

 

• Install piston seal, boot and piston to caliper referring 

to the following instructions.

1) Replace with a new piston seal (1) at every overhaul. 

After applying rubber grease (included in repair kit), 
fit piston seal (1) into groove in cylinder taking care 
not to twist it.

2) Before inserting piston (1) into cylinder, apply rubber 

grease (included in repair kit) to new boot “a” and 
install it onto piston as shown.

3) Fit boot as it is in figure into boot groove in cylinder 

with fingers.

4) Insert piston into cylinder by hand and fit boot in boot 

groove in piston.

I2RH01420013-

I2RH01420016-

“A”: 1 grooved side directed cylinder side
“B”: 2 grooved side directed pad side

1

I2RH01420017-

I4RS0A420006-

I2RH01420019-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Ecco Gemineye EC2014-C Installation Instructions Manual preview
Gemineye EC2014-C
Бренд: Ecco Страницы: 10
Ecco Reflex 5500 Series Installation And Operating Instructions Manual preview
Reflex 5500 Series
Бренд: Ecco Страницы: 12
Allen Sports QR545 Instructions preview
QR545
Бренд: Allen Sports Страницы: 2
Mercedes-Benz GUARD S 500 Supplement To Operators Manual preview
GUARD S 500
Бренд: Mercedes-Benz Страницы: 30
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
Hummer 2006 H2 Owner'S Manual preview
2006 H2
Бренд: Hummer Страницы: 502
JANE StrataPlatform Instructions Manual preview
StrataPlatform
Бренд: JANE Страницы: 58
Kia Sorento Owner'S Manual preview
Sorento
Бренд: Kia Страницы: 51
Mopar 77072498AB Manual preview
77072498AB
Бренд: Mopar Страницы: 18
Prorack K947 Fitting Instructions Manual preview
K947
Бренд: Prorack Страницы: 14
AllTrade Powerbuilt 648601 Operating Instructions preview
Powerbuilt 648601
Бренд: AllTrade Страницы: 3
Perrycraft SportQuest Series Installation preview
SportQuest Series
Бренд: Perrycraft Страницы: 2
Curt Group Aries AL235045 Installation Manual preview
Aries AL235045
Бренд: Curt Group Страницы: 2
Vauxhall Insignia 2009 Owner'S Manual preview
Insignia 2009
Бренд: Vauxhall Страницы: 253
Bracketron MULTI VEHICLE MOUNT MVM-45-05 Installation Manual preview
MULTI VEHICLE MOUNT MVM-45-05
Бренд: Bracketron Страницы: 4
Blue Ox BX2711 Installation Instructions Manual preview
BX2711
Бренд: Blue Ox Страницы: 8
Whelen Engineering Company SAK62D Installation Manual preview
SAK62D
Бренд: Whelen Engineering Company Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды