manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5C-6 Clutch: 

Installation

Reverse removal procedure for installation noting the 
following.

CAUTION:

• Do not allow fluid to get on painted 

surface.

• Do not allow pipe to contact hard against 

vehicle body or other parts.

 

• Install each clamp securely.
• After installation, check clutch pedal free travel and 

bleed air from system referring to “Clutch Pedal 
Inspection: ” and “Air Bleeding of Clutch System: ”.

• Check fluid leakage.
• Add fluid to MAX level of reservoir.

Clutch Fluid Pipe Inspection

S4RS0A5306026

Check pipe (1) for dent, kink, crack, dirt and dust. 
Replace if check result is not satisfactory.

Clutch Master Cylinder Removal and 
Installation

S4RS0A5306024

Removal

1) Clean around brake master cylinder reservoir cap 

and take out fluid with syringe or such from brake 
master cylinder reservoir.

2) Disconnect clutch fluid pipe from clutch master 

cylinder (1) referring to “Clutch Fluid Pipe Removal 
and Installation: ”.

3) Disconnect clutch reservoir hose (2).
4) Remove push rod from clutch pedal.
5) Turn clutch master cylinder (1) clockwise as shown 

in figure, and then remove it.

Installation

Reverse removal procedure for installation noting the 
following.
• Apply grease to push rod tip.

“A”:  Grease 99000–25100

Clutch Operating Cylinder Removal and 
Installation

S4RS0A5306025

Removal

1) Clean around brake master cylinder reservoir cap 

and take out fluid with syringe or such from brake 
master cylinder reservoir.

2) Disconnect clutch fluid pipe (2) from operating 

cylinder referring to “Clutch Fluid Pipe Removal and 
Installation: ”.

3) Remove clutch operating cylinder (1).

1

I4RS0A530007-

3. Brake booster

1

2

3

I4RS0A530008-

“A”

I4RS0A530009-

2

1

I4RS0A530010-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Бренд: IAME Страницы: 17
Jackco SHARP ALIGN User Manual preview
SHARP ALIGN
Бренд: Jackco Страницы: 11
Mobile Create MCM3 Instruction Manual preview
MCM3
Бренд: Mobile Create Страницы: 15
TUFLOC Dodge Charger TufBox Installation Instructions Manual preview
Dodge Charger TufBox
Бренд: TUFLOC Страницы: 6
PAC GM1A-R Quick Start Manual preview
GM1A-R
Бренд: PAC Страницы: 4
Big Mikes Performance Parts STO N SHO SNS 144 Installation Procedures Manual preview
STO N SHO SNS 144
Бренд: Big Mikes Performance Parts Страницы: 7
Lincoln MKZ 2018 Quick Reference Manual preview
MKZ 2018
Бренд: Lincoln Страницы: 10
Axxess AXRC-CH1 Installation Instructions Manual preview
AXRC-CH1
Бренд: Axxess Страницы: 8
Dodge Charger 1973 Body Service Manual preview
Charger 1973
Бренд: Dodge Страницы: 276
Cadillac 1999 Escalade Owner'S Manual preview
1999 Escalade
Бренд: Cadillac Страницы: 352
Yakima K896 Instructions Manual preview
K896
Бренд: Yakima Страницы: 12
Whispbar K835W Fitting Instructions For Basic Carrier preview
K835W
Бренд: Whispbar Страницы: 63
Cadillac STS 2011 Owner'S Manual preview
STS 2011
Бренд: Cadillac Страницы: 529
Toro 07389 Installation Instructions Manual preview
07389
Бренд: Toro Страницы: 16
Volvo XC60 2014 Wiring Diagrams preview
XC60 2014
Бренд: Volvo Страницы: 362
Buick 1997 Skylark Owner'S Manual preview
1997 Skylark
Бренд: Buick Страницы: 371
Brodit ProClip 854399 Installation Instructions preview
ProClip 854399
Бренд: Brodit Страницы: 2
Westin 28-0160 Instructions preview
28-0160
Бренд: Westin Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды