manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

8A-5 Seat Belts: 

Seat Belt

• The seat belt webbing or strap should be free from 

damage.

Retractor Assembly (with Seat Belt Pretensioner)

1) Let the seat belt retract fully to confirm its easy 

retraction.
• The retractor assembly should lock webbing when 

pulled quickly.

• The front seat belt retractor assembly (1) should 

pass the inspection and should lock webbing even 
when tilted (approx. 15

q

) toward the fore and aft or 

right and left directions.

2) Check retractor assembly (1) with seat belt 

pretensioner appearance visually for following 
symptoms and if any one of them is applicable, 
replace it with a new one as an assembly.
• Pretensioner has activated.
• There is a crack in seat belt pretensioner 

(retractor assembly).

• Seat belt pretensioner (retractor assembly) is 

damaged or a strong impact (e.g., dropping) was 
applied to it.

Anchor Bolt

• Anchor bolts should be torqued to specification.

Belt Latch

• It should be secure when latched.

Seat Belt Switch

Check driver side seat belt switch for continuity by using 
ohmmeter.

Seat belt switch specification
Without inserted buckle tongue to buckle catch:
Terminal “A” and “B”: Continuity
With inserted buckle tongue to buckle catch:
Terminal “A” and “B”: No continuity

I2RH01810005-

1. Buckle tongue
2. Buckle catch

I4RS0B810001-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Camcar 40104 Mounting Instructions preview
40104
Бренд: Camcar Страницы: 6
Trailboss HD86 Fitting Instructions preview
HD86
Бренд: Trailboss Страницы: 5
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Бренд: Club Car Страницы: 48
Raytel LLC TellPhone 4200 Installation Instructions & Operating Manual preview
TellPhone 4200
Бренд: Raytel LLC Страницы: 40
Parkeon StradaPAL Installation Manual preview
StradaPAL
Бренд: Parkeon Страницы: 43
Draw tite 24963 Installation Instructions preview
24963
Бренд: Draw tite Страницы: 4
EFILive CM2350B User Manual preview
CM2350B
Бренд: EFILive Страницы: 25
Paser UNICOM JVC Installation Manual preview
UNICOM JVC
Бренд: Paser Страницы: 2
Xblitz XME PRO User Manual preview
XME PRO
Бренд: Xblitz Страницы: 56
Cadillac STS 2011 Owner'S Manual preview
STS 2011
Бренд: Cadillac Страницы: 529
Toro 07389 Installation Instructions Manual preview
07389
Бренд: Toro Страницы: 16
RBO IT FITS RBO1018 Product Manual preview
IT FITS RBO1018
Бренд: RBO Страницы: 36
Brink 5978 Fitting Instructions Manual preview
5978
Бренд: Brink Страницы: 21
Arrista SG8-19 Installation Manual preview
SG8-19
Бренд: Arrista Страницы: 2
SSV Works RG4-DM3 Manual preview
RG4-DM3
Бренд: SSV Works Страницы: 2
Lund Tonno Pro Installation Instructions Manual preview
Tonno Pro
Бренд: Lund Страницы: 12
Metra Electronics 99-9302 Installation Instructions Manual preview
99-9302
Бренд: Metra Electronics Страницы: 8
Gigaware Gigaware 12-493 User Manual preview
Gigaware 12-493
Бренд: Gigaware Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды