manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-28 Automatic Transmission: 

Manual Road Test

S4RS0A5104012

This test checks the gears being used in “L”, “2” “3” or “D” range when driven with unoperated gear shift control 
system. Test drive vehicle on a level road.

NOTE:
Before this test, check DTC.

 

1) With select lever in “P”, start engine and warm it up.
2) After warming up engine, turn ignition switch OFF and disconnect valve body harness connector (1).

3) With select lever in “L” range, start vehicle and check that 3rd gear is being used referring to the following table.

Vehicle speed per 1000 rpm in engine speed

4) While vehicle is running, shift select lever to “2” range and check that 3rd gear is being used.
5) While vehicle is running, shift select lever to “3” or “D” range and check that 3rd gear is being used.
6) After the checks, stop vehicle then turn ignition switch OFF, and connect valve body harness connector.
7) Clear DTC.

TCC (lock-up) function 
pressure control does not 
operate

Malfunction of TCC pressure control 
solenoid valve

Inspect. If NG, replace.

Malfunction of shift solenoid valve-A 
and/or -B

Inspect. If NG, replace.

Malfunction of brake light switch

Inspect. If NG, replace.

Malfunction of engine coolant 
temperature sensor

Inspect. If NG, replace.

Malfunction of output shaft speed 
sensor (VSS)

Inspect. If NG, replace.

Malfunction of input shaft speed sensor

Inspect. If NG, replace.

Malfunction of throttle position sensor

Inspect. If NG, replace.

Malfunction of transmission range 
sensor

Inspect. If NG, replace.

Malfunction of transmission fluid 
temperature sensor

Inspect. If NG, replace.

Malfunction of pressure control solenoid 
valve

Inspect. If NG, replace valve body assembly.

Faulty valve body component

Replace valve body assembly.

Faulty torque converter

Replace.

Condition

Possible cause

Correction / Reference Item

Gear position

Vehicle speed

1st

9.2 km/h (5.7 mile/h)

2nd

16.8 km/h (10.4 mile/h)

3rd

26.4 km/h (16.4 mile/h)

4th

37.9 km/h (23.6 mile/h)

Reverse

11.7 km/h (7.3 mile/h)

I3RM0B510010-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

LAS BC260 Operating Instructions Manual preview
BC260
Бренд: LAS Страницы: 44
LAS 11807 Operating Instructions Manual preview
11807
Бренд: LAS Страницы: 24
Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Бренд: Yamaha Страницы: 3
Mobis G4211ADE00AL Installation Instructions Manual preview
G4211ADE00AL
Бренд: Mobis Страницы: 16
Subaru starlink Manual preview
starlink
Бренд: Subaru Страницы: 216
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
Fiat 500 L 2019 User Manual preview
500 L 2019
Бренд: Fiat Страницы: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Бренд: Honda Страницы: 6
Hummer 2006 H2 Owner'S Manual preview
2006 H2
Бренд: Hummer Страницы: 502
Metra Electronics 99-5819 Installation Instructions Manual preview
99-5819
Бренд: Metra Electronics Страницы: 8
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Бренд: Ranger design Страницы: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Бренд: AUTOTECH Страницы: 1
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Бренд: Over Armour Offroad Страницы: 9
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Бренд: r.LiNK Страницы: 21
Havis-Shields Telescoping Computer Base C-TCB-34 Install Instructions preview
Telescoping Computer Base C-TCB-34
Бренд: Havis-Shields Страницы: 1
PEUGEOT 106 2001 Owner'S Manual preview
106 2001
Бренд: PEUGEOT Страницы: 107
Axxess OESWC-LAN29H Installation Instructions Manual preview
OESWC-LAN29H
Бренд: Axxess Страницы: 8
Audi 2001 A3 Quick Reference Manual preview
2001 A3
Бренд: Audi Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды