manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

00-7 Precautions: 

Precaution for CAN Communication System

S4RS0A0000014

• The loose (1) in the wire harnesses twist of the CAN 

lines except around the connector (3) should be within 
100 mm (3.9 in.). Refer to the wiring diagram for the 
CAN lines discrimination. Excessively-loosed lines 
may be influenced by the electric noise.

• Do not connect terminals of the CAN line using a 

bypass wire (1). Otherwise, the CAN line may be 
influenced by the electric noise.

Precautions for Electrical Circuit Service

S4RS0A0000007

• When replacing a fuse, make sure to use a fuse of the 

specified capacity. Use of a fuse with a larger capacity 
will cause a damage to the electrical parts and a fire.

• When disconnecting and connecting coupler, make 

sure to turn ignition switch OFF, or electronic parts 
may get damaged.

• When disconnecting connectors, never pull the wiring 

harness. Unlock the connector lock first and then pull 
them apart by holding connectors themselves.

• When connecting connectors, also hold connectors 

and put them together until they lock securely (a click 
is heard).

• When installing the wiring harness, fix it with clamps 

so that no slack is left.

3

3

2

2

1

I4JA01000002-

1

I4JA01000003-

I2RH01010038-

I2RH01010039-

I2RH01010040-

I2RH01010041-

I2RH01010042-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

OEM Audio Reference Series Manual preview
Reference Series
Бренд: OEM Audio Страницы: 29
Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Бренд: Bimmer Jakes Страницы: 4
JANE be cool boosty Manual preview
be cool boosty
Бренд: JANE Страницы: 21
Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual preview
PRIME DESIGN VRI3-E-PM11
Бренд: Safe Fleet Страницы: 12
Barker 25895 Owner'S Instructions preview
25895
Бренд: Barker Страницы: 2
Prorack K383 Fitting Instructions Manual preview
K383
Бренд: Prorack Страницы: 14
Ironton 44596 Owner'S Manual preview
44596
Бренд: Ironton Страницы: 7
IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Бренд: IBASE Technology Страницы: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Бренд: Modifry Products Страницы: 2
RAM 1500 2WD 2021 Owner'S Manual preview
1500 2WD 2021
Бренд: RAM Страницы: 496
Quadratec 11113.1435 Quick Start Manual preview
11113.1435
Бренд: Quadratec Страницы: 14
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Бренд: AUTOTECH Страницы: 4
Axxess AXGMLN-09 Installation Instructions preview
AXGMLN-09
Бренд: Axxess Страницы: 4
RAM TRUCK 2500 2017 Owner'S Manual Supplement preview
TRUCK 2500 2017
Бренд: RAM Страницы: 33
Kargo Master PRO-II KS Assembly Instructions Manual preview
PRO-II KS
Бренд: Kargo Master Страницы: 8
Saab 2007 9-7X Owner'S Manual preview
2007 9-7X
Бренд: Saab Страницы: 498
Opel MERIVA 2014 Brochure & Specs preview
MERIVA 2014
Бренд: Opel Страницы: 44
Setma E12AU02002 Instruction Manual preview
E12AU02002
Бренд: Setma Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды