manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Hood / Fenders / Doors:  9J-1

Hood / Fenders / Doors

 

Repair Instructions

Hood Removal and Installation

S4RS0A9A06001

Removal

CAUTION:

Place cloth to prevent body from any 
damage.

 

1) Remove hood silencer (4).
2) Disconnect window washer hose (1) from hood.
3) Remove 4 mounting bolts (3) to detach hood (2).

Installation

Reverse removal procedure noting the following.
• Apply sealant to contact face “A” of hood hinge.

Specified sealant.

“A”:  Sealant 99000–31110

• Adjust hood lock position if necessary referring to 

“Hood Inspection and Adjustment”.

Hood Inspection and Adjustment

S4RS0A9A06002

Inspection

• Check that hood opens and closes smoothly and 

properly. Lubricate if necessary.

• Check that hood stops in the secondary latched 

position properly (preventing hood from opening 
freely) and that hood closes completely in the fully 
latched position.

• Adjust hood locks position, if necessary.

Adjustment

Adjust the following point:
• Hood position adjustment.

Fore-and-aft and right-and-left adjustment.
Adjust hood clearance by loosening hood mounting 
bolts. Refer to “Panel Clearance:  in Section 9K”.

• Vertical adjustment

If only one side (right or left) of hood is not level with 
front fender, make it level by tightening or loosening 
hood cushion (1).

• Hood lock position adjustment

a. Loosen hood lock bolts.
b. Adjust hood lock height position so the hood is 

locked without looseness.

c. Tighten hood latch bolts to specified torque.

Tightening torque
Hood latch bolt (a):  10 N·m (1.0 kg-m, 7.5 lb-ft)

d. Make sure the hood is locked smoothly and 

securely.

“A”

“A”

3

2

4

1

I4RS0A9A0001-

I2RH019A0022-

(a)

(a)

I4RS0A9A0002-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Vauxhall MOVANO Owner'S Manual preview
MOVANO
Бренд: Vauxhall Страницы: 177
GATmatic TWC-562S Installation, Operation & Maintenance Manual preview
TWC-562S
Бренд: GATmatic Страницы: 13
Mobile Create MCM3 Instruction Manual preview
MCM3
Бренд: Mobile Create Страницы: 15
Thule CIRCUIT 526XT Manual preview
CIRCUIT 526XT
Бренд: Thule Страницы: 12
AA Products RB0007 Instruction Manual preview
RB0007
Бренд: AA Products Страницы: 6
TATA Motors Tata Indigo Diesel Owner'S Manual & Service Book preview
Tata Indigo Diesel
Бренд: TATA Motors Страницы: 190
Safe Fleet Prime Design HBR-E-FT33B Assembly Instructions Manual preview
Prime Design HBR-E-FT33B
Бренд: Safe Fleet Страницы: 12
Bestop 51252 Installation Instructions preview
51252
Бренд: Bestop Страницы: 4
Safe Fleet Prime Design VBI-FT31B Assembly Instructions Manual preview
Prime Design VBI-FT31B
Бренд: Safe Fleet Страницы: 12
Mobridge DA-G2 MOST150 Manual preview
DA-G2 MOST150
Бренд: Mobridge Страницы: 20
Griffin Technology iTrip Bluetooth User Manual preview
iTrip Bluetooth
Бренд: Griffin Technology Страницы: 6
Mitsubishi Pajero Pinin 1999 Workshop Manual preview
Pajero Pinin 1999
Бренд: Mitsubishi Страницы: 919
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Бренд: RAM Страницы: 360
Menabo YELO 4 NS Fitting Instructions Manual preview
YELO 4 NS
Бренд: Menabo Страницы: 8
Subaru Forester 2.5X 2003 Technicians Reference Booklet preview
Forester 2.5X 2003
Бренд: Subaru Страницы: 44
Ratio Electric HOME BOX SMART Manual preview
HOME BOX SMART
Бренд: Ratio Electric Страницы: 16
Baby Jogger CITY GO PD349056A Assembly Instructions Manual preview
CITY GO PD349056A
Бренд: Baby Jogger Страницы: 16
Saab 12 832 509 Installation Instructions Manual preview
12 832 509
Бренд: Saab Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды