manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

0B-7 Maintenance and Lubrication: 

Fuel Filter Replacement

S4RS0A0206042

WARNING:

This work must be performed in a well 
ventilated area and away from any open 
flames (such as gas hot water heaters).

 

Fuel filter is installed in fuel pump assembly in fuel tank.
Replace fuel filter or fuel pump assembly with new one, 
referring to “Fuel Pump Assembly Removal and 
Installation:  in Section 1G” for proper procedure.

Fuel Tank Inspection

S4RS0A0206012

Check fuel tank damage, cracks, fuel leakage, corrosion 
and tank bolts looseness.
If a problem is found, repair or replace.

PCV Valve Inspection

S4RS0A0206013

Check crankcase ventilation hose and PCV hose for 
leaks, cracks or clog, and PCV valve for stick or clog. 
Refer to “PCV Valve Inspection:  in Section 1B” for PCV 
valve checking procedure.

Fuel Evaporative Emission Control System 
Inspection

S4RS0A0206014

1) Visually inspect hoses for cracks, damage, or 

excessive bends. Inspect all clamps for damage and 
proper position.

2) Check EVAP canister for operation and clog, 

referring to “EVAP Canister Inspection:  in Section 
1B”.
If a malfunction is found, repair or replace.

Brake Discs and Pads (Front) Inspection

S4RS0A0206015

1) Remove wheel and caliper but don’t disconnect 

brake hose from caliper.

2) Check front disc brake pads and discs for excessive 

wear, damage and deflection. Replace parts as 
necessary. For details, refer to “Front Disc Brake 
Pad Inspection:  in Section 4B” and “Front Brake 
Disc Inspection:  in Section 4B”.
Be sure to torque caliper pin bolts to specification.

Brake Drums and Shoes (Rear) Inspection

S4RS0A0206016

1) Remove wheel and brake drum.
2) Check rear brake drums and brake linings for 

excessive wear and damage, while wheels and 
drums are removed. At the same time, check wheel 
cylinders for leaks. Replace these parts as 
necessary.
For details, refer to “Rear Brake Drum and Shoe 
Inspection:  in Section 4C” and “Rear Brake Shoe 
Inspection:  in Section 4C”.

I4RS0A020019-

I4RS0A020006-

I3RM0A020006-

I4RS0A020007-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Davis Instruments 8127 Installation Instructions Manual preview
8127
Бренд: Davis Instruments Страницы: 16
Q'STRAINT QLK-150 Installation Instructions Manual preview
QLK-150
Бренд: Q'STRAINT Страницы: 10
Triumph MAYFLOWER 1951 Instruction Book preview
MAYFLOWER 1951
Бренд: Triumph Страницы: 86
Horn Tools HISDMSPTRA01 Mounting Instructions preview
HISDMSPTRA01
Бренд: Horn Tools Страницы: 6
Kargo Master 4A82T Installation Manual preview
4A82T
Бренд: Kargo Master Страницы: 6
Quadratec 12057.0263 Installation Manual preview
12057.0263
Бренд: Quadratec Страницы: 12
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Бренд: Whelen Engineering Company Страницы: 2
J. Strong JST506BT Installation Instructions preview
JST506BT
Бренд: J. Strong Страницы: 2
Z Flash OBD-II STALK User Manual preview
OBD-II STALK
Бренд: Z Flash Страницы: 4
true-i HMBS-200 User Manual preview
HMBS-200
Бренд: true-i Страницы: 11
Saab 2006 9-5 Owner'S Manual preview
2006 9-5
Бренд: Saab Страницы: 288
Curt Group 60638 Installation Manual preview
60638
Бренд: Curt Group Страницы: 3
Juna JRDAB-03 Installation Manual preview
JRDAB-03
Бренд: Juna Страницы: 10
Mazda 323F Owner'S Manual preview
323F
Бренд: Mazda Страницы: 196
Skoda Octavia 2007 Owner'S Manual preview
Octavia 2007
Бренд: Skoda Страницы: 288
Proxel EPS-DUAL Installation Instructions & User Manual preview
EPS-DUAL
Бренд: Proxel Страницы: 16
PAT ProPlus 620066V01 Operating Instructions Manual preview
ProPlus 620066V01
Бренд: PAT Страницы: 13
walser Crystalline Mounting Instruction preview
Crystalline
Бренд: walser Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды