manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-154 Automatic Transmission: 

18) Caulk reduction drive gear nut (1).

19) Apply A/T fluid to planetary gear assembly (1), then 

fit it to planetary ring gear assembly.

20) Check for correct installation of planetary gear 

assembly as follows.
Measure the distance “a” by using micrometer 
caliper (1) and straightedge (2). If measured value is 
out of specification, remove planetary gear assembly 
and reinstall it properly.

Distance between planetary gear assembly and 
mating surface of transaxle case
“a”: More than 49.9 m (1.965 in.)

21) Apply A/T fluid to one-way clutch No.2 assembly (1), 

then install it to planetary gear assembly. After that, 
ensure that planetary carrier rotates only in 
counterclockwise direction “A”, not in clockwise 
direction “B”.

22) Install one-way clutch outer race retainer (1).

I2RH0B510274-

1

I2RH0B510275-

“a”

“a”

2

1

I2RH0B510276-

I2RH0B510277-

I2RH0B510278-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

ULTIMATE SPEED CARBON Assembly And Safety Advice preview
CARBON
Бренд: ULTIMATE SPEED Страницы: 19
Wallbox Commander 2 Installation And User Manual preview
Commander 2
Бренд: Wallbox Страницы: 7
3SIXT 3S-1186 Operating Instructions Manual preview
3S-1186
Бренд: 3SIXT Страницы: 12
TATA Motors tigor Owner'S Manual preview
tigor
Бренд: TATA Motors Страницы: 159
Toro 137-1019 Installation Instructions Manual preview
137-1019
Бренд: Toro Страницы: 24
PAC Stinger ELEV8 Install Manual preview
Stinger ELEV8
Бренд: PAC Страницы: 14
Kolpin 98310 Product Instructions preview
98310
Бренд: Kolpin Страницы: 3
Skoda Superb 2006 Owner'S Manual preview
Superb 2006
Бренд: Skoda Страницы: 281
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Бренд: Over Armour Offroad Страницы: 9
DEFA MultiCharger 1204 User'S Installation Manual preview
MultiCharger 1204
Бренд: DEFA Страницы: 28
Steelmate PTS800V7 User Manual preview
PTS800V7
Бренд: Steelmate Страницы: 14
Whispbar K835W Fitting Instructions For Basic Carrier preview
K835W
Бренд: Whispbar Страницы: 63
Meritor 93000 Service Service Manual preview
93000 Service
Бренд: Meritor Страницы: 20
Stealthbox SB-J-GCHER2/10W3v2 Installation Manual preview
SB-J-GCHER2/10W3v2
Бренд: Stealthbox Страницы: 2
Scosche HAQ02 Quick Start Manual preview
HAQ02
Бренд: Scosche Страницы: 8
Nav TV NTV-KIT850 Install Manual preview
NTV-KIT850
Бренд: Nav TV Страницы: 11
Adaptiv Mini CAM-MB6-AD User Manual preview
CAM-MB6-AD
Бренд: Adaptiv Mini Страницы: 4
Hyundai Sonata 2011 Owner'S Manual preview
Sonata 2011
Бренд: Hyundai Страницы: 380

Бренды по названию

Популярные бренды

Загрузить еще бренды