manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

4C-3 Rear Brakes: 

9) Install wheel and tighten wheel nuts to specified 

torque.

Tightening torque
Wheel nut (a):  85 N·m (8.5 kg-m, 61.5 lb-ft)

10) Check to ensure that brake drum is free from 

dragging and proper braking is obtained. Then 
remove vehicle from hoist and perform brake test 
(foot brake and parking brake).

Rear Brake Drum and Shoe Inspection

S4RS0A4306003

Brake Drum

Inspect brake drum for wear.
If limit value of drum inner diameter is exceeded or 
uneven or stepped wear is excessive, replace drum.

Drum inner diameter “a”
Standard: 200 mm (7.87 in.)
Limit: 202 mm (7.95 in.)

Cracked, Scored or Grooved Drum

A cracked drum is unsafe for further service and must be 
replaced. Do not attempt to weld a cracked drum.
Smooth up any slight scores. Heavy or extensive scoring 
will cause excessive brake lining wear and it will 
probably be necessary to resurface drum braking 
surface.
If brake linings are slightly worn and drum is grooved, 
drum should be polished with fine emery cloth but should 
not be turned.

NOTE:
When drum is removed, visually inspect 
wheel cylinder for brake fluid leakage. 
Correct leaky point, if any.

 

Brake Shoe

Measure thickness of brake shoe (1). Also, check 
surface of lining for hardening, excessive wear and oil.

Brake shoe thickness ( shoe rim)
Standard: 5.6 mm (0.22 in.)
Limit: 2.6 mm (0.10 in.)

CAUTION:

Never polish lining with sandpaper. If lining is 
polished with sandpaper, hard particles of 
sandpaper will be deposited in lining and 
may damage drum. When it is required to 
correct lining, replace it with a new one.

 

ABS Sensor Ring Removal and Installation (If 
Equipped)

S4RS0A4306009

CAUTION:

Do not reuse (reinstall) removed ABS sensor 
ring.

 

Removal

1) Remove brake drum referring to “Rear Brake Drum 

Removal and Installation: ”.

2) Remove sensor ring (1) from brake drum (2) using 

special tools.

CAUTION:

Pull out sensor ring from brake drum 
gradually and evenly. Attempt to pull it out 
partially may cause it to be deformed.

 

Special tool
(A):  09913–75520
(B):  09913–65135

I2RH01430011-

I4RS0A430008-

I2RH01430007-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

JETBAG 320 Fitting Instructions Manual preview
320
Бренд: JETBAG Страницы: 44
Eaton Green Motion Building Quick Start Manual preview
Green Motion Building
Бренд: Eaton Страницы: 12
FANATEC Porsche 911 Turbo S Wheel Developer Quick Manual preview
Porsche 911 Turbo S Wheel
Бренд: FANATEC Страницы: 9
Honda HRM3000 User Manual preview
HRM3000
Бренд: Honda Страницы: 73
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Бренд: GOgroove Страницы: 9
Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Бренд: Monacor Страницы: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Бренд: Jeep Страницы: 338
Doug Thorley Headers THY-464-1 Instructions preview
THY-464-1
Бренд: Doug Thorley Headers Страницы: 5
Edelbrock 66002 Installation Instructions preview
66002
Бренд: Edelbrock Страницы: 2
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Бренд: Chrysler Страницы: 1534
Hama 00178266 Operating Instruction preview
00178266
Бренд: Hama Страницы: 75
Safe Fleet PRIME DESIGN VRR-NV200 Manual preview
PRIME DESIGN VRR-NV200
Бренд: Safe Fleet Страницы: 12
BrandMotion FLTW-7690 Installation Instructions preview
FLTW-7690
Бренд: BrandMotion Страницы: 2
SAN HIMA SH-TENT-SY20 User Manual preview
SH-TENT-SY20
Бренд: SAN HIMA Страницы: 7
Paccar Peterbilt SmartAir Operator'S Manual preview
Peterbilt SmartAir
Бренд: Paccar Страницы: 58
Mercedes-Benz 300 SL Operator'S Manual preview
300 SL
Бренд: Mercedes-Benz Страницы: 153
Kia Picanto Manual preview
Picanto
Бренд: Kia Страницы: 680
Broadfeet RSLX-385-68S Installation Instructions preview
RSLX-385-68S
Бренд: Broadfeet Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды